Einhell TС-CS 1200 - Инструкция по эксплуатации - Страница 20

GB

- 20 -

on the front of the saw foot. 

• 

 You can now adjust the cutting angle to 

around 45°. Keep an eye on the cutting angle 

scale (9) as you do so.

• 

 Refasten the locking lever for miter setting (7). 

Check the handle is securely fastened.

5.3 Extraction of dust and chips (Figure 6)

• 

 Connect a suitable vacuum cleaner to the 

provided chip extractor connector (14) of your 

circular saw (vacuum cleaner not included). 

This will provide excellent dust extraction on 

the workpiece. The benefits are that you will 

protect both the equipment and your own 

health. Your work area will also be cleaner 

and safer.

• 

 Dust created when working may be dange-

rous. Refer to the section entitled “Safety inst-

ructions”.

• 

 Important! The vacuum cleaner you use for 

the extraction work must be suitable for the 

workpiece material.

• 

 Check that all the parts are properly connec-

ted.

5.4 Parallel stop (Figure 7/8)

• 

 The parallel stop (16) enables you to saw par-

allel lines.

• 

 Loosen the locking screw for the parallel stop 

(8) on the saw foot (6).

• 

 To assemble, slide the parallel stop (16) into 

the guide (a) on the saw foot (6) (see Figure 

7)

• 

 Set the required spacing and then tighten the 

locking screw (8) again.

• 

 Using the parallel stop: Position the parallel 

stop (16) flat on the edge of the workpiece 

and start the cut.



 Important! Carry out a trial cut in a piece 

of waste wood

6. Operation

6.1 Working with the hand-held circular saw

• 

 Always hold the circular saw firmly.

• 

 The swing guard hood (19) is pushed back 

automatically by the workpiece.

• 

 Do not use force!

• 

Push forwards gently and evenly with the 

circular saw.

• 

 The waste piece should be on the right-hand 

side of the circular saw so that the wide 

section of the support bench supports its full 

area.

• 

 If you are sawing down a line that has been 

drawn, guide the circular saw along the corre-

sponding notch.

• 

 Clamp small pieces of wood securely before 

sawing them. Never hold them with your 

hand.

• 

 Always follow the safety instructions. Wear 

safety goggles.

• 

 Do not use defective saw blades or blades 

that are cracked or broken.

• 

 Do not use any flanges / flange nuts whose 

bore hole is larger or smaller than those in the 

saw blade.

• 

 The saw blade must not be decelerated by 

hand or by applying lateral pressure to the 

blade.

• 

 The swing guard hood must not jam and must 

return to its initial position after the operation 

has been completed.

• 

  Before you use the machine, ensure that the 

safety equipment such as the swing guard 

hood, splitter, flanges and adjustment de-

vices are in working order and are correctly 

adjusted and secure.

• 

You can connect a suitable dust extraction 

system to the sawdust extraction connector 

(14). Ensure that the dust extractor line is sa-

fely and correctly connected.

• 

The moving swing guard hood must not be 

fixed in the retracted guard hood when the 

saw is in use.

• 

Saw blades whose main body is thicker or 

tooth set thinner than the thickness of the 

splitter must not be used.



 Important. Always pull out the power plug 

before doing any work on the circular saw!

6.2 Using the circular saw

• 

 Adjust the cutting depth, cutting angle and 

parallel stop (see section 5.1, 5.2 and 5.4)

• 

 Ensure that the ON/OFF switch (2) is not 

depressed. Only then should you connect the 

mains plug to a suitable socket.

• 

 Do not switch on the circular saw until you 

have fitted a saw blade.

• 

 Place the saw foot flat on the workpiece you 

wish to saw. The saw blade must not be in 

contact with the workpiece.

• 

 Hold the circular saw firmly with both hands.

Anl_TC_CS_1200_SPK9.indb   20

Anl_TC_CS_1200_SPK9.indb   20

12.12.2019   08:43:44

12.12.2019   08:43:44