Bosch 0.603.3C7.002 - Инструкция по эксплуатации - Страница 19

 English | 

19

Bosch Power Tools

1 609 92A 32F | (16.8.16)

When the LED indicator 

17

continuously lights up red

, the 

temperature of the battery is too high and the machine 
switches off automatically.
– Switch the power tool off.
– Allow the battery to cool down before continuing to work.

The LED indicator 

17

flashes red

, the power tool is blocked 

and switches off automatically.

Remove the power tool from the workpiece.

The power tool will continue to work as soon as the blockage 
is rectified.

Protection Against Deep Discharging

The lithium-ion battery is protected against deep discharging 
by the “Electronic Cell Protection (ECP)”. When the battery is 
empty, the machine is switched off by means of a protective 
circuit: The inserted tool no longer rotates.

Switching on the LED Work Area Illumination

The power light 

27

 lights up when the On/Off switch 

4

 is 

slightly or completely pressed, and allows the work area to be 
illuminated when lighting conditions are insufficient.

Working Advice

Protect saw blades against impact and shock.

Guide the machine evenly and with light feed in the cutting di-
rection. Excessive feed significantly reduces the service life of 
the saw blade and can cause damage to the power tool.

Sawing performance and cutting quality depend essentially 
on the condition and the tooth form of the saw blade. There-
fore, use only sharp saw blades that are suited for the material 
to be worked.

Sawing Wood

The correct selection of the saw blade depends on the type 
and quality of the wood and whether lengthway or crossway 
cuts are required.

When cutting spruce lengthways, long spiral chips are 
formed.

Beech and oak dusts are especially detrimental to health. 
Therefore, work only with dust extraction.

Sawing with Parallel Guide (see figure D)

The parallel guide 

33

 enables exact cuts along a workpiece 

edge and cutting strips of the same dimension.

Mount the parallel guide 

33

 to the machine using the fasten-

ing bolt 

8

.

Adjust the parallel guide 

33

 to the requested cutting width.

Sawing with Auxiliary Guide (see figure E)

For sawing large workpieces or straight edges, a board or 
strip can be clamped to the workpiece as an auxiliary guide; 
the base plate of the circular saw can be guided alongside the 
auxiliary guide.

Working with Parallel Guide and Vacuum Hose

First mount the extraction adapter 

30

 with vacuum hose 

31

and then the parallel guide 

33

.

Note: 

Use only the intended screws to fix the parallel guide 

33

and the extraction adapter 

30

!

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Store the battery only within a temperature range between 
– 20 ° C and 50 ° C. As an example, do not leave the battery in 
the car in summer.

Occasionally clean the venting slots of the battery using a soft, 
clean and dry brush.

A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.

Observe the notes for disposal.

Maintenance and Service

Maintenance and Cleaning



Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport 
and storage, remove the battery from the power tool. 

There is danger of injury when unintentionally actuating 
the On/Off switch.



For safe and proper working, always keep the machine 
and ventilation slots clean.

The retracting blade guard must always be able to move freely 
and retract automatically. Therefore, always keep the area 
around the retracting blade guard clean. Remove dust and 
chips by blowing out with compressed air or with a brush.

Saw blades that are not coated can be protected against cor-
rosion with a thin coat of acid-free oil. Before use, the oil must 
be removed again, otherwise the wood will become soiled.

Resin and glue residue on the saw blade produces poor cuts. 
Therefore, clean the saw blade immediately after use.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare 
parts. Exploded views and information on spare parts can al-
so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions 
concerning our products and their accessories.

In all correspondence and spare parts orders, please always 
include the 10-digit article number given on the nameplate of 
the product.

Great Britain

Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange 
the collection of a product in need of servicing or repair. 
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com

OBJ_BUCH-2942-001.book  Page 19  Tuesday, August 16, 2016  11:43 AM