Bosch 0.601.675.000 - Инструкция по эксплуатации - Страница 14

14

 | English 

1 609 929 Y20 | (13.7.11)

Bosch Power Tools

f

Do not use the power tool if the switch does not turn it 

on and off. 

Any power tool that cannot be controlled with 

the switch is dangerous and must be repaired.

f

Disconnect the plug from the power source and/or the 

battery pack from the power tool before making any 

adjustments, changing accessories, or storing power 

tools. 

Such preventive safety measures reduce the risk of 

starting the power tool accidentally.

f

Store idle power tools out of the reach of children and 

do not allow persons unfamiliar with the power tool or 

these instructions to operate the power tool. 

Power 

tools are dangerous in the hands of untrained users.

f

Maintain power tools. Check for misalignment or bind-

ing of moving parts, breakage of parts and any other 

condition that may affect the power tool’s operation. If 

damaged, have the power tool repaired before use. 

Many accidents are caused by poorly maintained power 

tools.

f

Keep cutting tools sharp and clean. 

Properly maintained 

cutting tools with sharp cutting edges are less likely to bind 

and are easier to control.

f

Use the power tool, accessories and tool bits etc. in ac-

cordance with these instructions, taking into account 

the working conditions and the work to be performed. 

Use of the power tool for operations different from those 

intended could result in a hazardous situation.

Service

f

Have your power tool serviced by a qualified repair per-

son using only identical replacement parts. 

This will en-

sure that the safety of the power tool is maintained.

Safety Warnings for Circular Saws

Cutting procedures

f

DANGER: Keep hands away from cutting area and the 

blade. Keep your second hand on auxiliary handle, or 

motor housing. 

If both hands are holding the saw, they 

cannot be cut by the blade.

f

Do not reach underneath the workpiece. 

The guard can-

not protect you from the blade below the workpiece.

f

Adjust the cutting depth to the thickness of the work-

piece. 

Less than a full tooth of the blade teeth should be 

visible below the workpiece.

f

Never hold piece being cut in your hands or across your 

leg. Secure the workpiece to a stable platform. 

It is im-

portant to support the work properly to minimize body ex-

posure, blade binding, or loss of control.

f

Hold the power tool by the insulated gripping surfaces 

only, when performing an operation where the cutting 

tool may contact hidden wiring or its own cord. 

Contact 

with a “live” wire will also make exposed metal parts of the 

power tool “live” and could give the operator an electric 

shock.

f

When ripping always use a rip fence or straight edge 

guide. 

This improves the accuracy of cut and reduces the 

chance of blade binding.

f

Always use blades with correct size and shape (dia-

mond versus round) of arbour holes. 

Blades that do not 

match the mounting hardware of the saw will run eccentri-

cally, causing loss of control.

f

Never use damaged or incorrect blade washers or bolt. 

The blade washers and bolt were specially designed for 

your saw, for optimum performance and safety of opera-

tion.

f

Kickback causes and related warnings 

– Kickback is a sudden reaction to a pinched, bound or 

misaligned saw blade, causing an uncontrolled saw to lift 

up and out of the workpiece toward the operator;

– When the blade is pinched or bound tightly by the kerf 

closing down, the blade stalls and the motor reaction 

drives the unit rapidly back toward the operator;

– If the blade becomes twisted or misaligned in the cut, 

the teeth at the back edge of the blade can dig into the top 

surface of the wood causing the blade to climb out of the 

kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect oper-

ating procedures or conditions and can be avoided by tak-

ing proper precautions as given below.

f

Maintain a firm grip with both hands on the saw and po-

sition your arms to resist kickback forces. Position 

your body to either side of the blade, but not in line with 

the blade. 

Kickback could cause the saw to jump back-

wards, but kickback forces can be controlled by the opera-

tor, if proper precautions are taken.

f

When blade is binding, or when interrupting a cut for 

any reason, release the trigger and hold the saw mo-

tionless in the material until the blade comes to a com-

plete stop. Never attempt to remove the saw from the 

work or pull the saw backward while the blade is in mo-

tion or kickback may occur. 

Investigate and take correc-

tive actions to eliminate the cause of blade binding.

f

When restarting a saw in the workpiece, centre the saw 

blade in the kerf and check that saw teeth are not en-

gaged into the material. 

If saw blade is binding, it may 

walk up or kickback from the workpiece as the saw is re-

started.

f

Support large panels to minimise the risk of blade 

pinching and kickback. 

Large panels tend to sag under 

their own weight. Supports must be placed under the pan-

el on both sides, near the line of cut and near the edge of 

the panel.

f

Do not use dull or damaged blades. 

Unsharpened or im-

properly set blades produce narrow kerf causing excessive 

friction, blade binding and kickback.

f

Blade depth and bevel adjusting locking levers must be 

tight and secure before making cut. 

If blade adjustment 

shifts while cutting, it may cause binding and kickback.

f

Use extra caution when sawing into existing walls or 

other blind areas. 

The protruding blade may cut objects 

that can cause kickback.

Guard function

f

Check guard for proper closing before each use. Do not 

operate the saw if guard does not move freely and en-

OBJ_BUCH-1471-001.book  Page 14  Wednesday, July 13, 2011  10:56 AM