Bosch GBH 36 V LI Plus - Инструкция по эксплуатации - Страница 19

 English | 

19

Bosch Power Tools

1 609 92A 0JA | (22.6.15)

Removing the Key Type Drill Chuck

– Push the locking sleeve 

5

 toward the rear and pull out the 

key type drill chuck 

23

.

Removing/Inserting the Quick Change Chuck 
(GBH 36 VF-LI Plus)

The SDS-plus quick change chuck 

2

 can easily be replaced 

against the quick change keyless chuck 

1

 provided.

Removing the Quick Change Chuck (see figure D)

– Pull the lock ring for the quick change chuck 

6

 toward the 

rear, hold it in this position and pull off the SDS-plus quick 
change chuck 

2

 or the quick change keyless chuck 

1

 to-

ward the front.

– After removing, protect the replacement chuck against 

contamination.

Inserting the Quick Change Chuck (see figure E)



Use only model-specific original equipment and pay at-
tention to the number of identification grooves 26.On-
ly quick-change chucks with two or three identification 
grooves are permitted. 

When an unsuitable quick-change 

chuck is used, the application tool could fall out during op-
eration.

– Before inserting, clean the quick change chuck and apply a 

light coat of grease to the shank end.

– Grasp the SDS-plus quick change chuck 

2

 or the quick 

change keyless chuck 

1

 completely with your hand. Slide 

the quick change chuck with a turning motion onto the drill 
chuck mounting 

25

 until a distinct latching noise is heard.

– The quick change chuck is automatically locked. Check the 

locking effect by pulling the quick change chuck.

Changing the Tool

The dust protection cap 

4

 largely prevents the entry of drilling 

dust into the tool holder during operation. When inserting the 
tool, take care that the dust protection cap 

4

 is not damaged.



A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by 
an after-sales service.

Changing the Tool (SDS-plus)

Inserting SDS-plus Drilling Tools (see figure F)

The SDS-plus drill chuck allows for simple and convenient 
changing of drilling tools without the use of additional tools.

– GBH 36 VF-LI Plus: Insert the SDS-plus quick change 

chuck 

2

.

– Clean and lightly grease the shank end of the tool.
– Insert the tool in a twisting manner into the tool holder until 

it latches itself.

– Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus drilling tool can 
move freely. This causes a certain radial run-out at no-load, 
which has no effect on the accuracy of the drill hole, as the 
drill bit centres itself upon drilling.

Removing SDS-plus Drilling Tools (see figure G)

– Push back the locking sleeve 

5

 and remove the tool.

Changing the Tool (without SDS-plus)
(GBH 36 V-LI Plus)

Inserting (see figure H)
Note: 

Do not use tools without SDS-plus for hammer drilling 

or chiselling! Tools without SDS-plus and their drill chucks are 
damaged by hammer drilling or chiselling.

– Insert a key type drill chuck 

23

 (see “Inserting/Removing 

the Key Type Drill Chuck”, page 18).

– Open the key type drill chuck 

23

 by turning until the tool 

can be inserted. Insert the tool.

– Insert the chuck key into the corresponding holes of the 

key type drill chuck 

23

 and clamp the tool uniformly.

– Turn the mode selector switch 

13

 to the “drilling” position.

Removing (see figure I)

– Turn the sleeve of the key type drill chuck 

23

 with the drill 

chuck key in anticlockwise direction until the drilling tool 
can be removed.

Changing the Tool (without SDS-plus)
(GBH 36 VF-LI Plus)

Inserting (see figure J)
Note: 

Do not use tools without SDS-plus for hammer drilling 

or chiselling! Tools without SDS-plus and their drill chucks are 
damaged by hammer drilling or chiselling.

– Insert the quick change keyless chuck 

1

.

– Firmly hold the retaining ring 

29

 of the quick change 

chuck. Open the tool holder by turning the front sleeve 

28

until the tool can be inserted. Tightly hold the retaining ring 

29

 and firmly turn the front sleeve 

28

 in the direction of the 

arrow until a distinct latching noise can be heard.

– Check the tight seating by pulling the tool.

Note: 

If the tool holder was opened to the stop, then the latch-

ing noise possibly may be heard while closing the tool holder 
and the tool holder will not close.
In this case, turn the front sleeve 

28

 once in the opposite di-

rection of the arrow. Afterwards, the tool holder can be 
closed (tightened) again.

– Turn the mode selector switch 

13

 to the “drilling” position.

Removing (see figure K)

– Firmly hold the retaining ring 

29

 of the quick change 

chuck. Open the tool holder by turning the front sleeve 

28

in the direction of the arrow until the tool can be removed.

Dust Extraction with GDE 16 Plus (Accessory)



Dusts from materials such as lead-containing coatings, 
some wood types, minerals and metal can be harmful to 
one’s health. Touching or breathing-in the dusts can cause 
allergic reactions and/or lead to respiratory infections of 
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered 
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials 
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable 

for the material.

– Provide for good ventilation of the working place.

OBJ_BUCH-283-012.book  Page 19  Monday, June 22, 2015  10:28 AM