Bosch GBH 240 - Инструкция по эксплуатации - Страница 13

 English | 

13

Bosch Power Tools

1 609 92A 3SE | (24.4.17)



Keep children and bystanders away while operating a 

power tool. 

Distractions can cause you to lose control.

Electrical safety



Power tool plugs must match the outlet. Never modify 

the plug in any way. Do not use any adapter plugs with 

earthed (grounded) power tools. 

Unmodified plugs and 

matching outlets will reduce risk of electric shock.



Avoid body contact with earthed or grounded surfaces, 

such as pipes, radiators, ranges and refrigerators. 

There is an increased risk of electric shock if your body is 
earthed or grounded.



Do not expose power tools to rain or wet conditions. 

Water entering a power tool will increase the risk of electric 
shock.



Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away 

from heat, oil, sharp edges 

or

 moving parts. 

Damaged 

or entangled cords increase the risk of electric shock.



When operating a power tool outdoors, use an exten-

sion cord suitable for outdoor use. 

Use of a cord suitable

for outdoor use reduces the risk of electric shock.



If operating a power tool in a damp location is unavoid-

able, use a residual current device (RCD) protected 

supply. 

Use of an RCD reduces the risk of electric shock. 

Personal safety



Stay alert, watch what you are doing and use common 

sense when operating a power tool. Do not use a power 

tool while you are tired or under the influence of drugs, 

alcohol or medication. 

A moment of inattention while op-

erating power tools may result in serious personal injury.



Use personal protective equipment. Always wear eye 

protection. 

Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection 
used for appropriate conditions will reduce personal 
injuries.



Prevent unintentional starting. Ensure the switch is in 

the off-position before connecting to power source 

and/or battery pack, picking up or carrying the tool. 

Carrying power tools with your finger on the switch or 
energising power tools that have the switch on invites 
accidents.



Remove any adjusting key or wrench before turning 

the power tool on. 

A wrench or a key left attached to a ro-

tating part of the power tool may result in personal injury.



Do not overreach. Keep proper footing and balance at 

all times. 

This enables better control of the power tool in 

unexpected situations.



Dress properly. Do not wear loose clothing or jewel-

lery. Keep your hair, clothing and gloves away from 

moving parts. 

Loose clothes, jewellery or long hair can be

caught in moving parts.



If devices are provided for the connection of dust 

extraction and collection facilities, ensure these are 

connected and properly used. 

Use of dust collection can 

reduce dust-related hazards.

Power tool use and care



Do not force the power tool. Use the correct power tool 

for your application. 

The correct power tool will do the

job better and safer at the rate for which it was designed.



Do not use the power tool if the switch does not turn it 

on and off. 

Any power tool that cannot be controlled with 

the switch is dangerous and must be repaired.



Disconnect the plug from the power source and/or the 

battery pack from the power tool before making any 

adjustments, changing accessories, or storing power 

tools. 

Such preventive safety measures reduce the risk of 

starting the power tool accidentally.



Store idle power tools out of the reach of children and 

do not allow persons unfamiliar with the power tool or 

these instructions to operate the power tool. 

Power 

tools are dangerous in the hands of untrained users.



Maintain power tools. Check for misalignment or bind-

ing of moving parts, breakage of parts and any other 

condition that may affect the power tool’s operation. If 

damaged, have the power tool repaired before use. 

Many accidents are caused by poorly maintained power 
tools.



Keep cutting tools sharp and clean. 

Properly maintained 

cutting tools with sharp cutting edges are less likely to bind 
and are easier to control.



Use the power tool, accessories and tool bits etc. in ac-

cordance with these instructions, taking into account 

the working conditions and the work to be performed. 

Use of the power tool for operations different from those 
intended could result in a hazardous situation.

Service



Have your power tool serviced by a qualified repair 

person using only identical replacement parts. 

This will

ensure that the safety of the power tool is maintained.

Hammer Safety Warnings



Wear ear protectors. 

Exposure to noise can cause 

hearing loss.



Use auxiliary handle(s), if supplied with the tool. 

Loss 

of control can cause personal injury.



Hold the tool by the insulated gripping surfaces when 

performing operations where the application tool or 

the screw could contact hidden wiring or its own power 

cord. 

Contact with a “live” wire will also make exposed 

metal parts of the power tool “live” and shock the operator.



Use suitable detectors to determine if utility lines are 

hidden in the work area or call the local utility company 

for assistance. 

Contact with electric lines can lead to fire 

and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or 
may cause an electric shock.



Secure the workpiece. 

A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.



When working with the machine, always hold it firmly 

with both hands and provide for a secure stance. 

The

power tool is guided more secure with both hands.

OBJ_BUCH-2460-003.book  Page 13  Monday, April 24, 2017  10:03 AM