AEG KH 5 G - Инструкция по эксплуатации - Страница 9

6

GB

Switch the device off immediately if the insertion tool stalls! Do 

not switch the device on again while the insertion tool is stalled, 

as doing so could trigger a sudden recoil with a high reactive force. 

Determine why the insertion tool stalled and rectify this, paying 

heed to the safety instructions.
Possible causes can be:

•  it is tilted in the workpiece to be machined

•  breakage of the material to be used

•  the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use. 

WARNING! Danger of burns

•  when changing tools

•  when setting the device down
Chips and splinters must not be removed while the machine is 

running.
Always disconnect the plug from the socket before carrying out any 

work on the machine.

MAINS CONNEC TION

Connect only to single-phase AC system voltage as indicated on 

the rating plate. It is also possible to connect to sockets without an 

earthing contact as the design conforms to safety class II.
Appliances used at many different locations including wet room 

and open air must be connected via a residual current device (FI, 

RCD, PRCD) of 30mA or less.
Only plug-in when machine is switched off.

SPECIFIED CONDITIONS OF USE

The pneumatic hammer can be universally used for hammer drilling 

and chiselling in stone and concrete.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times.
If the supply cord of this appliance is damaged, it must only be 

replaced by a repair shop appointed by the manufacturer, to avoid 

hazardous situations.
Use only AEG accessories and spare parts. Should components 

need to be replaced which have not been described, please contact 

one of our AEG service agents (see our list of guarantee/service 

addresses).
If needed, an exploded view of the tool can be ordered. Please state 

the Article No. as well as the machine type printed on the label 

and order the drawing at your local service agents or directly at: 

Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnen-

den, Germany.

EC-DECL ARATION OF CONFORMIT Y

We declare under our sole responsibility that the product described 

under “Technical Data” fulfills all the relevant provisions of the 

directives 

2011/65/EU (RoHS) 

2006/42/EC 

2014/30/EU 

and the following harmonized standards have been used.
EN 60745-1:2009 + A11:2010

EN 60745-2-6:2010

EN 55014-1:2006 + A1:2009 + A2:2011

EN 55014-2:1997 + A1:2001 + A2:2008

EN 61000-3-2:2014

EN 61000-3-3:2013 

EN 50581:2012

English

 Winnenden, 2016-02-12

Alexander Krug / Managing Director

Authorized to compile the technical file
Techtronic Industries GmbH

Max-Eyth-Straße 10, 71364 Winnenden, Germany

SYMBOLS

CAUTION! WARNING! DANGER!

Always disconnect the plug from the socket before 

carrying out any work on the machine.

Please read the instructions carefully before starting the 

machine.

Accessory - Not included in standard equipment, available 

as an accessory.
Do not dispose of electric tools together with household waste 

material. Electric tools and electronic equipment that have 

reached the end of their life must be collected separately and 

returned to an environmentally compatible recycling facility. 

Check with your local authority or retailer for recycling advice 

and collection point.
Class II tool. Tool in which protection against electric shock 

does not rely on basic insulation only, but in which additional 

safety precautions, such as double insulation or reinforced 

insulation, are provided. There being no provision for protec-

tive earthing or reliance upon installation conditions.
European Conformity Mark

UkrSEPRO Conformity Mark

EurAsian Conformity Mark