Tefal Access Steam Force DT8270E1 - Инструкция по эксплуатации - Страница 4

6

7

abnormally in any way. Do not attempt to dismantle your 

appliance: have it examined at an Approved Service Centre to 

avoid any danger.

•  The iron should only be used with the base provided (for 

cordless irons).

•  Check the electrical power for sign of wear or damage prior 

to use. If the electrical power cord is damaged, it must 

be replaced at an Approved Service Centre to avoid any 

danger.

•  Do not use other descaling products than the one cited in 

the IFU.

•  To achieve optimal results in sanitizing, gently steam back 

and forth 3 times on the fabric

Before first use

•  When you first use the appliance, some smoke or a harmless odour may be produced or there may be a small discharge of 

particles. This will not affect the use of the appliance and will disappear quickly.

What water to use?

•  Your appliance has been designed to use tap water.

If your water is very hard (hardness above 30°F, or 17°dH or 21°e), mix 50% tap water and 50% bottled demineralised 

water. Never use water containing additives (starch, perfume, aromatic substances, softeners, etc.), or condensation water (for 

example water from tumble dryers, water from refrigerators, water from air conditioning units, rainwater). Do not use pure 

distilled nor pure demineralised water. Such water contains organic waste materials or minerals that concentrate under the 

effect of heat and cause spitting, brown colouring or premature ageing of your appliance.

SAVE THESE INSTRUCTIONS

Environment protection first !

i

 Your appliance contains valuable materials which can be recovered or recycled.



Leave it at a local civic waste collection point.

PROBLEM

POSSIBLE CAUSES

SOLUTIONS

There is no steam.

The appliance is not plugged in, or not 

switched on.

Check that your appliance is correctly 

plugged in and switched on.

The water level is too low.

Unplug your appliance and refill it.

The steam pump has not been primed.

Press the steam trigger continuously for a 

few seconds to begin steaming.

You are using the appliance for the 

first time.

Press the steam trigger continuously for a 

few seconds to begin steaming.

The water tank is not fully in place.

Ensure that stopper is closed and that the 

water tank snaps when put into place.

The appliance is on standby mode.

PLEASE REFER TO THE ‘STANDBY’ 

section.

The appliance does not 

heat.

It is not plugged in, or not switched on.

Plug in your appliance and switch on.

The appliance is on standby mode.

PLEASE REFER TO THE ‘STANDBY’ 

section.

Water leaks.

The water tank is not fully in place or the 

stopper is not closed properly.

Ensure that stopper is closed and that the 

water tank snaps when put into place.

Steam rate decreases.

Calc Sealing

Refer to ‘ANTI CALC section in 

instructions for use.

The steam leaves stains 

on the fabric or the 

appliance spits

You are using water with additives.

Never add any additive in the water tank.

The appliance has not been cleaned 

enough after the descaling operation.

Read carefully the ‘ANTI CALC’ section in 

instructions for use.

You are using other liquids than white 

vinegar to descale the product.

Use only white vinegar during ‘ANTI 

CALC’ procedure.

Appliance steams 

continuously.

The steam trigger is on the lock position. or 

you have activated the continuous steam 

by quick double clic on steam trigger

Unlock the steam trigger or you must click 

one time on steam trigger to unlock it

The continuous steam 

stop suddenly

The continuous steam stop  automatically 

after 1minute for double clic appliances

If you want to restart the continuous 

steam, you must operate a quick double 

clic on steam trigger again.

The steam head is 

dripping

You have used the steam boost too often 

(for appliance equipped with a steam 

boost)

Limit steam boost usage at 3 times a 

minute maximum. Separate those boosts 

by 20 seconds minimum.

Problems with your iron?