BRAYER BR4120 - Инструкция по эксплуатации - Страница 4

6

7

EN

EN

THE UNIT IS INTENDED FOR HOUSEHOLD USE 

ONLY, DO NOT USE THE UNIT FOR COMMERCIAL 

OR LABORATORY PURPOSES.

BEFORE THE FIRST USE
After the unit’s transportation or storage at negative 

temperature, unpack it and wait for at least 3 hours 

before using it.

•  Unpack the unit and remove all the packaging 

materials. 

• 

If there is a protective film on the operating surface 

(5), remove it.

•  Keep the original package.

•  Read the safety measures and operating 

recommendations.

•  Check the delivery set.

•  Examine the unit for damages, in case of damage do 

not plug it into the mains.

• 

Make sure that specified specifications of power 

supply voltage of the unit correspond to the 

specifications of your mains. When using the unit in 

the mains with 60 Hz frequency, the unit does not 

need any additional settings.

•  Wipe the garment steamer body with a slightly damp 

cloth and then wipe it dry.

GARMENT STEAMER PURPOSE 

- The garment steamer can be used for careful 

smoothing of folds on clothes or furniture. 

- If you have doubts about steaming any certain 

kind of fabric or clothes, you should follow the 

recommendations on the product label. 
- If no such information is available, try to steam the 

fabric on the reverse side. 
- When steaming such fabrics as silk or corduroy, keep 

the garment steamer at some distance from the fabric. 
- Use the brush attachment (11) to remove lint or 

threads from the fabric. 

STEAMER OPERATION
WATER SELECTION 

•  Fill the water tank (1) with tap water. If tap water is 

hard, we recommend mixing it with distilled water 

in proportion 1:1. If tap water is too hard, mix it with 

distilled water in proportion 1:2 or use distilled water 

only. 

ATTENTION!
Before detaching the water tank (1), make sure that 

the power plug (9) is not inserted into the mains 

socket.

•  Take the water tank by both sides and remove it. 

•  Open the water inlet lid (2). Fill the water tank (1) with 

water non exceeding the MAX mark and close the 

water inlet lid (2) tightly. 

• 

Do not fill the tank (1) with carbonated water, 

perfume additives, vinegar, chemical agents, etc.

•  Install the water tank (1) back to its place and make 

sure that the tank (1) is fixed properly. 

ATTENTION!
Do not plug the garment steamer in if the water tank 

(1) is empty.

• 

Place the garment steamer on the base (10) on a flat 

and steady surface.

•  Connect the power plug (9) to the mains socket, 

press the ON/OFF button (7) « », the indicator 

(6) will light up and start flashing. When the set 

temperature is reached, the indicator (6) will glow 

constantly.

•  Take the garment steamer by the handle (8) on the 

same level with the steam supply on button (4).

•  To switch the steam supply on, press and hold down 

the button (4).

• 

To switch the steam supply off release the button (4).

•  For continuous steam supply, move the lock (3) 

downwards, to switch the continuous steam supply 

on, move the lock (3) upwards.

•  Before general use of the garment steamer clean the 

steam chamber. To do this, direct the outgoing steam 

to a piece of cloth, for instance, try to smooth out a 

kitchen towel.

•  If during the operation the water tank (1) becomes 

empty, switch the garment steamer off before 

removing the tank (1) and refilling it with water, press 

and hold the ON/OFF button (7) « », disconnect 

the power plug (9) from the mains socket. To do this, 

disconnect the power plug (9) from the mains socket.

• 

After the unit operation switch the garment steamer off, 

remove the power plug (9) from the mains socket and let 

the garment steamer cool down.

Note:

 when switching the unit on for the first time, foreign 

smell can appear. It is normal.

ATTENTION!

If the garment steamer is switched on and does not operate 

for 8 minutes, the heating element will switch off and the 

indicator (6) will be flashing. To switch the garment steamer 

on, press the steam supply button (4) or the ON/OFF button 

(7) « », the garment steamer will switch on; wait until the 

indicator (6) glows constantly and continue the operation. 

USING THE BRUSH ATTACHMENT
ATTENTION!
Before installing the brush attachment (11) and 

removing the tank (1), make sure that the power plug 

(9) is not inserted into the mains socket.

•  Install the brush attachment (11) on the garment 

steamer.

•  Remove the water tank (1). 

•  Open the water inlet lid (2). Fill the water tank (1) with 

water non exceeding the MAX mark and close the water 

inlet lid (2) tightly. 

• 

Do not fill the tank (1) with carbonated water, perfume 

additives, vinegar, chemical agents, etc.