Einhell TE-DH 50 - Инструкция по эксплуатации - Страница 18

GB

- 18 -

L

pA

 sound pressure level  ...................... 101 dB(A)

K

pA

 uncertainty  ............................................. 3 dB

L

WA

 sound power level   ..................... 103.8 dB(A)

K

WA

 uncertainty ............................................. 3 dB

Wear ear-mu

ff

 s.

The impact of noise can cause damage to hea-

ring.

Total vibration values (vector sum of three direc-

tions) determined in accordance with EN 60745.

Chiseling

Vibration emission value a

h

 = 22.9m/s

2

K uncertainty = 1.5 m/s

2

The speci

fi

 ed vibration value was established in 

accordance with a standardized testing method. 

It may change according to how the electric 

equipment is used and may exceed the speci

fi

 ed 

value in exceptional circumstances.

The speci

fi

 ed vibration value can be used to 

compare the equipment with other electric power 

tools.

The speci

fi

 ed vibration value can be used for initi-

al assessment of a harmful e

ff

 ect.

Keep the noise emissions and vibrations to a 

minimum.

• 

 Only use appliances which are in perfect wor-

king order.

• 

 Service and clean the appliance regularly.

• 

 Adapt your working style to suit the appliance.

• 

 Do not overload the appliance.

• 

 Have the appliance serviced whenever ne-

cessary.

• 

 Switch the appliance off when it is not in use.

• 

 Wear protective gloves.

Caution!

Residual risks

Even if you use this electric power tool in 

accordance with instructions, certain resi-

dual risks cannot be rules out. The following 

hazards may arise in connection with the 

equipment’s construction and layout:

1.   Lung damage if no suitable protective dust 

mask is used.

2.   Damage to hearing if no suitable ear protec-

tion is used.

3.   Health damage caused by hand-arm 

vibrations if the equipment is used over a 

prolonged period or is not properly guided 

and maintained.

Danger! 

The electric power tool generates an electro-

magnetic 

fi

 eld during operation. Under certain 

circumstances this 

fi

 eld may actively or passively 

impede medical implants. To reduce the risk of 

serious or fatal injuries, we recommend persons 

with medical implants to consult their doctor and 

the manufacturer of the medical implant prior to 

using the equipment.

5.  Before starting the equipment

Before you connect the equipment to the mains 

supply make sure that the data on the rating plate 

are identical to the mains data.

Warning! 

Always pull the power plug before making 

adjustments to the equipment.

Before using the tool, use a to cable/pipe detector 

to check the point of use for concealed electrical 

cables, gas pipes and water pipes.

5.1 Additional handle (Fig. 2)

For safety reasons you must only use the 

demolition hammer with the additional handle.

The additional handle (3) enables you to achieve 

better stability while using the demolition hammer. 

The additional handle (3) can be turned to any 

required position: 

• 

To do this, undo the fastening for the 

additional handle (4).

• 

Now turn or tilt the additional handle (3) into 

the most comfortable working position for you 

and then tighten the fastening (4) again.

5.2 Inserting the tool (Fig. 3-4)

Before inserting it, clean the tool and lightly 

grease the shaft of the tool.

1.  Pull out the locking bolt (5) as far as possible 

and hold it.

2.  Turn it through 180° and release it. It does not 

matter which direction you turn it in.

3.  Guide the tool with the 

fl

 at side facing the bolt 

into the tool chuck (6) and slide it in as far as 

it will go.

4.  Pull out the locking bolt (5) again and hold it.

5.  Turn it through 180° again and release it. It 

does not matter which direction you turn it in.

Anl_TE_DH_50_SPK9.indb   18

Anl_TE_DH_50_SPK9.indb   18

12.09.2018   08:52:47

12.09.2018   08:52:47