Bosch GSH 500 - Инструкция по эксплуатации - Страница 11

English | 

11

Additional Safety Instructions

u

Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility com-
pany for assistance.

 Contact with electric lines can lead

to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.

u

Always wait until the power tool has come to a com-
plete stop before placing it down.

 The application tool

can jam and cause you to lose control of the power tool.

u

Secure the workpiece.

 A workpiece clamped with

clamping devices or in a vice is held more secure than by
hand.

u

Do not touch any application tools or adjacent housing
components shortly after operation. 

These can become

very hot during operation and cause burns.

u

Take care when carrying out demolition work using
the chisel.

 Falling fragments of the demolition material

could injure you or any bystanders.

Products sold in GB only:

Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.

u

Hold the power tool firmly with both hands and make
sure you have a stable footing.

 The power tool can be

more securely guided with both hands.

Product Description and
Specifications

Read all the safety and general instructions.

Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.

Please observe the illustrations at the beginning of this oper-
ating manual.

Intended use

The power tool is intended for chiselling work in concrete,
brick, stone and asphalt, as well as for driving in and com-
pressing with the appropriate accessories.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.

(1)

Dust protection cap

(2)

Locking sleeve

(3)

Chisel adjustment ring (Vario-Lock)

(4)

Lock-on button for on/off switch

(5)

On/off switch

(6)

Handle (insulated gripping surface)

(7)

Auxiliary handle (insulated gripping surface)

Technical Data

Demolition hammer

GSH 500

Article number

3 611 C38 7..

Rated power input

W

1100

Impact rate

min

-1

2900

Chisel positions

12

Impact energy per stroke
according to EPTA-Proced-
ure 05:2016

J

7.5

Tool holder

SDS-max

Lubrication

Grease lubrication

Weight according to EPTA-
Procedure 01:2014

kg

5.7

Protection class

 / II

The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.

Noise/Vibration Information

Noise emission values determined according to

EN IEC 62841-2-6

.

Typically, the A-weighted noise level of the power tool is:
Sound pressure level 

89

 dB(A); sound power level

100

 dB(A). Uncertainty K=

3

 dB.

Wear hearing protection

Vibration total values a

h

 (triax vector sum) and uncertainty K

determined according to 

EN IEC 62841-2-6

:

Chiselling: a

h

 = 

15.5

 m/s

2

, K = 

1.5

 m/s

2

The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.

Bosch Power Tools

1 609 92A 77U | (28.07.2022)