Vitek VT-2173 - Инструкция по эксплуатации - Страница 4

4

 ENGLISH

•  Provide that water does not get on the 

control panel of the unit.

•  If some water gets on the fan heater, 

before touching it you should unplug it 
in order to avoid risk of getting electric 
shock.

•  Do not decline the unit while moving it in 

order to avoid its turnover and splashing 
of water. 

•  Do not move the appliance by the cord. 
•  Always unplug the unit before cleaning or 

filling the water tank with water.  

•  Do not touch the plug with wet hands.
•  Never wind the cord over the case of 

the unit. Use special holders to wind the 
cord. 

•  Do not switch on and do not use the fan 

heater if a cord or a plug is damaged or 
if the fan heater works irregularly, fell or 
is damaged. Apply to service centers for 
testing and repair. 

•  If you are not going to use the unit for 

a long time, drain the remaining water 
before storage, dry the water tank and 
the cell evaporator, and place the unit 
for keeping. Keep the unit in a dry cool 
place.

•  To remove dirt use soft detergents, do 

not use abrasives.  

•  Do not leave the unit operating while 

sleeping.

• 

The climatic station is intended for 
household use only.

Attention:

If the unite filled with water falls, discon-
nect it immediately and place the unit ver-
tically. Turn the water tank clamp (16) anti 
clockwise and remove the water tank (13). 
Remove the drain plug (17) and drain wa-
ter. Before switching on the unit you should 
apply to a service center for testing and re-
pair, if necessary.  

Before first usage

•  Unpack the unit.

•  Make sure that an electricity supply cor-

responds to the voltage of current speci-
fied on the housing. Switch on the unit 
using the power switch (7) by setting it to 
the “ON” position, two sound signals will 
be heard and the ON indication (40) will 
be flashing.

Functions of the buttons on the control 
panel
Note:

 The buttons on the remote control 

corresponds to the buttons on the control 
panel. Each pressing of the button is ac-
companied by a sound signal.  

The “ВКЛ./СКОРОСТЬ” (ON/SPEED) 
button

To switch on the unit press the (22) “ВКЛ./
СКОРОСТЬ” button, a sound signal will be 
heard. The unit will operate at middle air flow 
speed; the following indications will light 
up: middle air flow indication (29) “СРЕД”, 
ionization mode (27), “ОБЫЧНЫЙ” oper-
ating mode (37) ВКЛ indication (40). In 3 
seconds the unit will switch to the minimal 
air flow speed mode, the “НИЗ” indication 
(28) will light up.
Use the (22) “ВКЛ./СКОРОСТЬ” button 
to select the air flow speed: high (“ВЫС”), 
middle (“СРЕД”) or low (“НИЗ”), the corre-
sponding indication will be displayed (28), 
(29) or (30). 

The “ВЫКЛ” (OFF) button

While pressing of the (26) “ВЫКЛ” button 
the unit will switch to standby mode. The 
(40) “ВКЛ” indication will start flashing.

Note:

 While pressing of the (26) “ВЫКЛ” 

button in the heating mode the unit will 
switch to the standby mode in about 10 
seconds. 

The “ПОВОРОТ Ж АЛЮЗИ” (JALOUSIE 
TURN) button

While pressing of the (24) “ПОВОРОТ 

4

2173.indd   4

2173.indd   4

17.07.2008   9:55:55

17.07.2008   9:55:55