TESY CN 04 300 MIS F 304825 - Инструкция по эксплуатации - Страница 5

Operation and Storage Manual

5

EN

English

a pulling rope in order to move the panel heater; 

any movement of the panel heater should be done 

when it is cold. 

 •

Position the panel heater with installed feet on the 

floor and before connecting it to the power socket 

check if all instructions from the very beginning of 

this manual have been followed correctly (Important 

instructions and safety measures). The correct 

position is – the control panel should be at the top of 

the appliance and the feet – on the floor!

BATHROOM OPERATION

 •

The panel heater must be installed in accordance 

with the normal trade practices and in compliance 

with the national legislation (EU electricity directives 

and regulations concerning special installations and 

places of operation including bathrooms, shower 

cabins HD60364-7-701(IEC 60364-7-701:2006)).

 •

In case this panel heater is to be used in a bathroom 

or other similar room, the following installation 

requirements must be observed: the panel heater 

is with IP24 protection (water drops protection). 

Hence it can be installed in “Volume 2” (see the 

diagram below) in order to avoid the risk of the 

control board (power switch and thermo regulator) 

being reached by a person who is in a shower or 

a bathtub. The minimum distance between the 

appliance and a water source should be not less 

than 1 meter! If you do not feel sure about the 

installation of this panel heater in a bathroom, 

we recommend you to consult a professional 

electrician.

Note

: If the above-mentioned instructions cannot be 

implemented, it is recommended to install the appliance 

in “VOLUME 3”. 

 •

In wet premises the power source must be installed 

at a height of at least 25 cm above the floor 

(bathrooms and kitchens).

 •

The installation must be equipped with a safety 

fuse, and the distance between the fuse contacts in 

disconnected condition should be at least 3 mm. 

OPERATION INSTRUCTIONS

MECHANICAL CONTROL 

Operation modes 

Turn the panel heater on 

by pushing the switch in 

position “I”  (turned-on  ), 

then turn the regulator to 

the desired level (1 to 6) as 

you take into account the 

following relation between 

the power levels:

* – anti-freezing mode/ 

enabled when room 

temperature falls below 7°C

1 / 2 

– economy mode/ 

it maintains low room 

temperature/ this mode is recommended to be used 

at night and when there are no people present in the 

room. This mode permits to maintain the set room 

temperature while saving energy. 

3 / 4 / 5

 – comfort mode/ it maintains moderate room 

temperature/ this mode is recommended to be used to 

maintain relatively high comfortable room temperature 

during the day. 

6

 – maximum power mode / it maintains HIGH room 

temperature/ this mode is recommended to be used 

when you need maximum high room temperature

Important: 

Thermo Regulator digits do not correspond 

to certain room temperature levels, but they can be used 

by users to memorize the relation between room temperature 

and the thermo regulator settings. For fine adjustment you can 

use thermometer- as you follow the principle of room 

temperature measurement for a few hours (it is set according 

to the size of the heated premises).

When the room temperature is lower than the 

temperature that you have set by the thermo regulator, 

the panel heater starts its operation and will operate 

until the room temperature reaches the set temperature 

level of the unit. When the room temperature is higher 

than the adjusted temperature of the appliance, the 

panel heater will automatically go into “Stand by” mode. 

PROTECTION 

 •

The appliance is equipped with a safety thermo 

turn-off device, which automatically turns the 

heater off in cases of extreme temperature of the 

panel heater /i.e. overheating of the appliance/.

 •

The safety thermo turn-off device will automatically 

restore the heater operation when the temperature 

of the appliance falls below the permissible ultimate 

values.