Обогреватели TESY CN 04 300 MIS F 304825 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
4
Operation and Storage Manual
EN
grilles; do not hamper the incoming and outgoing air
flow. All objects must be at a safe distance of at least 1
meter away from the appliance front and sides.
•
The most common reason for overheating is dust
and fluff deposits in the appliance. Clean the
ventilation openings on a regular basis with a
vacuum cleaner, but before that it is very important
to disconnect the heater from the mains.
•
Never touch the appliance with wet or moist hands
– there is risk for your life!
•
The power socket should be accessible all the time
in order to disconnect the power plug when needed
as fast as possible! Never pull the power cord or the
appliance itself in order to disconnect it from the mains.
•
PAY ATTENTION! Outgoing air gets heated during
appliance operation (up to more than 100°С).
•
If the power cord of the appliance gets damaged,
stop the heater and call its supplier/retailer for
further instructions.
•
If you decide to stop using an appliance of this kind,
it is recommended to make it unusable by cutting
its power cord after you have disconnected it from
the mains. It is advisable all possible risks related to
the appliance to be secured, especially in relation to
children that may play with out-of-use appliances.
•
The appliance must not be placed right under a
socket box!
•
Warning: Do not use this appliance with a programmer,
counter or any other mechanism which could
automatically turn on the heater – if the appliance
is covered or positioned incorrectly there is a risk of fire.
•
Position the power cord in such a way that it does
not obstruct the free movement of people and
cannot be stepped on! Use only approved extension
cords, which are suitable for this appliance, i.e. they
have a compliance sign!
•
Never move the appliance by pulling its power cord;
do not use the power cord for carrying other objects!
•
Do not bend the power cord and do not pull it
against sharp edges; do not place the power cord
on hot surfaces or open fire!
PACKING
•
After unpacking the appliance, check if its contents
are intact and if it has not been damaged during
transportation! In case a damage or incomplete
delivery is found, contact your authorized retailer!
•
Do not dispose of the original packing box! It could
be used for storage and transportation purposes in
order to avoid damages during transportation!
•
Disposal of packing material should be done in the
appropriate way! Children must be prevented from
playing with polyethylene bags!
OPERATION AND INSTALLATION OF FEET SET
•
This panel heater is designed to be used indoors.
Important
: In premises bigger than 45 m
3
, it is
recommended to use a combination of 2 or more
panel heaters.
•
Do not position the panel heater under a power
socket or electricity connection box.
•
DO NOT install/operate the panel heater:
1.
in places where a draught is present, which
could influence the control settings;
2.
right under a power socket;
3.
in “Volume 1” for bathrooms;
4.
in “Volume 2” if the control board can be
reached by a person who is in a shower or in a
bathtub;
•
Before starting the set installation check if the panel
heater is disconnected from the power socket!
•
The feet are to be installed at side of the air inlets
– it is correct them to be installed at the two sides
ends of the panel heater in a symmetrical on the
appointed place (see picture below). For installation
purposes – all panel heaters have got 2 openings for
every foot.
•
Mount the first foot on the appointed place. Then
you should screw the two securing screws. The
screw goes through the plastic foot and gets
screwed into plastic nut based on panel heater. You
should repeat the same operation for the second
foot.
•
The joint is secure in case the panel heater stands
horizontally on the floor after its feet installation
has been completed. Do not use the power cord as
