FRICO AD220E12 - Инструкция по эксплуатации - Страница 24

Thermozone AD  200 A/E

  23

GB

Start-up

Note! When using for the irst time or when starting up 

after a long period of disuse, a small amount of smoke 
and a slight odour may occur temporarily, which is 
completely normal. 

Trouble shooting

If the fans stand still, check the following:
a) Power supply; check fuses, circuit-breaker,  

time switch (if any) that starts and stops    
the unit.

b) That the air low selector is correctly set.

c)  That the position limit switch is working  

(if any).

If the error cannot be ixed, please contact qualiied 

service technician.

If there is no heat, check the following:
a) Power supply to electric heater; check fuses and  

circuit-breaker (if any).

b) Thermostat settings and actual temperature. 
c)  That the output selector (if any) is set correctly.
d) That the overheat protection has not been released. 

Overheating
(applies to units with electric heat)

The Thermozone is equipped with an overheat protec-
tor. If it is released due to overheating, reset as follows:
1) Disconnect the electricity with the fully  

isolated switch.

2) Investigate the matter and repair the fault.
3) Reset is performed as follows:

  • Locate the red button which is located inside 

  the unit at the inner gable to which the fan and  

the motor are attached. You can see it if you remove 
the front plate, see page 2.

  • Press the button until a click is heard  

4) Connect the Thermozone again.

If the error cannot be ixed, please contact qualiied 

service technician.

Maintenance

NOTE!

 Disconnect electricity prior to cleaning or inspec-

tion (units with electric heat can be supplied from more 
than one connection).

The fan motors and the other components require 

no maintenance other than cleaning when necessary, 
however at least once year. 

Note! Units provided with aluminium heating ele

-

ments shall be inspected and if necessery cleaned on a 

reguarly basis.

 Grille, impeller and elements are vacuum 

cleaned or dried clean with a damp cloth. Open the 

inspection hatch to reach elements and impellers.

Residual current circuit breaker
(applies to units with electric heater)

When the installation is protected by means of a 
residual current circuit breaker, which trips when the 
appliance is connected, this may be due to moisture 
in the heating element. When an appliance containing 
a heater element has not been used for a long period 
or stored in a damp environment, moisture can enter 
the element. This should not be seen as a fault, but is 

simply rectiied by connecting the appliance to the mains 

supply via a socket without a safety cut-out, so that the 
moisture can be eliminated from the element. The drying 
time can vary from a few hours to a few days. As a 
preventive measure, the unit should occasionally be run 

for a short time when it is not being used for extended 

periods of time.

The garantee is only valid if the Thermozone 
units are used in the manner intended by the 
manufacturer and in accordance with the 
installation and maintenance instructions.

Safety

• For all installations of electrically heated products 

should a residual current circuit breaker 300 mA for ire 

protection be used.

• Keep the areas around the air intake and exhaust gril

-

les free from possible obstructions!

• During operation the surfaces of the unit can be hot!

• The unit must not be fully or partially covered with clo

-

thing, or similar materials, as overheating can result in a

ire risk! (E)

• This appliance is not intended for use by persons (in

-

cluding children) with reduced physical, sensory or men-

tal capabilities, or lack of experience and knowledge, 

unless they have been given supervision or instruction 
concerning use of the appliance by a person responsible

for their safety. Children should be supervised to ensure 

that they do not play with the appliance.