FIRST FA-5571-3 White - Инструкция по эксплуатации - Страница 2

FUNCTION OPERATION 

(both machine & remote control)

1.   Plug in and switch on by pressing the red 

switch 0/I, enter into standby mode and 

display shows “   ”:

2.   Press ” 

 “ button enter into fan mode, see 

below: 

3.   Press “ 

 “ button for one time, the product 

works with low heating and display show 

” -- / I ”, see below: A. Press second time, 

changes to high heating and display show 

” -- / I / II ”, see below: B. 

4.  Press ” 

 “ button to set timer (00-12hours). 

Pressing the button one time increases one 

hour for timer. After setting time, the display 

will show current setting time for 5 seconds, 

then resume to previous display, meanwhile 

the light of ” 

 “ will on. Below photo (C) is 

an example of setting 8h:

A

B

C

5.  Appointment “ON”: In standby mode, 

press ” 

 “ timer button, you can set the 

appointment turn-on time in 00-12 hours. 

After complete setting, the display shows 

the appointment turn-on time and also the 

light ” 

 “ is on. The display automatically 

decreases 1 hour for each hour passed. 

When the appointment power-on time 

arrived, the product will automatically turns 

on. The default setting temperature is 23°C 

during appointment turn-on. Below photos is 

an example to set appointment turn-on time 

to 8 hours: 

Note: 

If not setting the temperature and weekly 

program, the product will automatically turn-off 

after 12 hours of continuous work, and enter 

into standby. 

FUNCTION OPERATION 

(ONLY by remote control)

1.   Set current TIME/DAY (can set both under 

standby mode & working status):

   Press ”SET” button for one time, the display 

shows ”12“ as default, press “+/−“ to set 

current hour (total in 24 hours); press “SET“ 

again, the display shows minute “30“, press 

“+/−“ to set current minute (00~59 minutes), 

then press “SET“ for third time, the display 

shows the day “d7”, press “+/−“ to set 

current day (Monday-Sunday: d1-d7). Then 

press ”OK“ to confirm the setting, the display 

will show previous settings. 

  For example: Setting to Wednesday, 9:30 

AM under 25°C under II heating, pls. refer to 

the following photos:

Note: 

-  If main switch off, power cut off, or plug out, 

it need reset. 

-   Press ”SET“ to check the current time & day 

in turn;

2.   Set temperature

  During working status, press “+/−“, the 

display shows ”23“ as default. Press “+/−“ to 

set desired temperature (temperature range 

10-49°C), press ”OK“ to confirm the setting. 

  For example: The current ambient 

temperature is 15°C, when set temperature 

to 25°C, the display shows as below:

Note:

When setting temperature, it will use SMART 

working way:

1)  Setting temperature – ambient temperature 

>2°C, working with high power;

2)  0°C <Setting temperature – ambient 

temperature =<2°C, working with low power;

3)  Setting temperature – ambient temperature 

=0°C, the cool fan will work for 30 seconds 

to below out the heating left inside, then 

enter into standby mode. 

3

ENGLISH

2

ENGLISH

INSTRUCTION MANUAL

Please read this instruction manual carefully

to obtain the best results. 

CONNECTIONS TO MAIN SUPPLY

Make sure the supply voltage in your home is 

the same as the voltage marked on the rating

plate of the appliance. 

Warning: risk of fire, electric shock, physical 

injuries and material damage. 
Before using this appliance, always follow 

the safety advice during assembly, use and 

maintenance. 

SAFETY INSTRUCTIONS

1.   The heater should be hung on the wall and 

the wind outlet should face down or be 

placed on flat appliance. You must not place 

it precipitantly or tipsily.

2.   Please do not use the heater in places full 

of combustible or explosive gas. Don’t cover 

the wind outlet.

3.    If the supply cord is damaged, it must be 

replaced by the manufacturer or its service 

agent or a similarly qualified person in order 

to avoid a hazard 

4.    If nobody is in or you are repairing the heater, 

please disconnect the heater from electric 

outlet.

5.   Please don’t touch the heater with wet 

hands or other conductors.

6.   Motor is out of order, please make it stop 

immediately.

7.   During use, please do not open the door or 

window otherwise it will diminish the heating 

effect.

8.   To turn off the machine, press the on/off 

switch to off, then the machine will keep the 

fan working about 30 seconds until it blows 

out cool wind, then the machine will stop 

working and you can take out the plug.

9.   Must hang the heater on the wall and fix it 

away from water in bathroom.

10.  Remote control, please use 1x CR2025 

battery.

11.  If the product needs repair, please ask 

experts or our company authorized 

maintenance department.

12.  This appliance is not intended for use by 

persons (including children) with reduced 

physical, sensory or mental capabilities, or 

lack of experience and knowledge, unless 

they have been given supervision or 

instruction concerning use of the appliance 

by a person responsible for their safety.

13.  Children should be supervised to ensure 

that they do not play with the appliance.

14. 

Cleaning and user maintenance shall not be 

made by children without supervision. 

15. Children of less than 3 years should be kept 

away unless continuously supervised. 

16. 

Children aged from 3 years and less than 8 

years shall only switch on/off the appliance 

provided that it has been placed or installed 

in its intended normal operating position 

and they have been given supervision or 

instruction concerning use of the appliance 

in a safe way and understand the hazards 

involved. Children aged from 3 years and 

less than 8 years shall not plug in, regulate 

and clean the appliance or perform user 

maintenance. 

17. 

CAUTION - Some parts of this product can 

become very hot and cause burns. Particular 

attention has to be given where children and 

vulnerable people are present. 

18. CAUTION: In order to avoid a hazard due 

to inadvertent resetting of the thermal 

cutout, this appliance must not be supplied 

through an external switching device, such 

as a timer, or connected to a circuit that is 

regularly switched on and off by the utility. 

19. 

WARNING: In order to avoid overheating, do 

not cover the heater. 

20. The heater must not be located immediately 

below a socket-outlet. 

21. 

Means for disconnection having a contact 

separation in all poles must be incorporated 

in the fixed wiring in accordance with the 

wiring rules. 

22. 

The heater must be installed at least 1.8m 

above the floor. 

23. 

Do not use this heater in the immediate 

surroundings of a bath, a shower or 

swimming pool. 

WARNING:

Don’t touch the working machine and don’t 

cover the wind outlet and inlet!

INSTALLATION 

(see picture A):

Drill two holes into the wall and keep a distance 

of 1.8m from the ground. The diameter of the 

hole just contains the inflated plastic pipe. After 

tucking the inflated plastic pipe, fix pothook on 

the pipe with screws. Make sure pothook are 

safely placed and hang the heater. The clip 

under the pothook should be inserted rabbet of 

the heater bottom.