Skil 0761 - Инструкция по эксплуатации - Страница 8

8

MAINTENANCE / SERVICE

•  This tool is not intended for professional use

•  Before maintenance always switch off tool, ensure 

there is no water pressure in tool and hand gun, 

disconnect plug from power source, and disconnect 

tool from water supply

•  Always keep tool and cord clean (especially ventilation 

slots S 

2

)

-  do not use water, solvents or polishes

-  regularly clean spraying nozzle G using cleaning 

needle M 

0

 (remove spray lance K from hand gun L 

first)

•  Regularly check for worn or damaged components and 

have them repaired/replaced when necessary

•  Cleaning water filter

-  remove water filter E 

2

 from inlet connector C 

2

 with 

long nose pliers

-  rinse it clean and put it back (replace it when 

damaged)

!  never use the tool with a damaged water filter

•  Storage 

!

-  store the tool out of reach of children in a location 

where the ambient temperature will not exceed 40°C 

or drop below 0°C

-  do not place other objects on top of the tool

-  securely mount storage rail N on the wall with 4 screws 

(

not supplied

) and horizontally leveled

-  use storage rail N and storage straps P as illustrated

•  If the tool should fail despite the care taken in 

manufacturing and testing procedures, repair should be 

carried out by an after-sales service centre for SKIL 

power tools

-  send the tool 

undismantled

 together with proof of 

purchase to your dealer or the nearest SKIL service 

station (addresses as well as the service diagram of 

the tool are listed on www.skil.com)

TROUBLESHOOTING

•  The following listing shows problem symptoms, possible 

causes and corrective actions (if these do not identify 

and correct the problem, contact your dealer or service 

station)

!  switch off the tool and disconnect the plug before 

investigating the problem

★ Spray is not consistent

-  nozzle partly blocked -> clean nozzle

★ Motor does not start or stops suddenly

-  power supply socket faulty -> use another socket

-  plug not connected -> connect plug

-  thermal protection switched off the motor -> let the tool 

cool down for 5 minutes

★ Motor is running but spray is poor

-  nozzle completely blocked -> clean nozzle

-  water filter clogged -> clean water filter

-  air in the pump -> ensure that water inlet connector is 

securely fitted

-  inadequate water supply -> check that water tap is 

fully open

ENVIRONMENT

• 

Do not dispose of electric tools, accessories and 

packaging together with household waste material

(only for EU countries)

-  in observance of European Directive 2012/19/EC on 

waste of electric and electronic equipment and its 

implementation in accordance with national law, 

electric tools that have reached the end of their life 

must be collected separately and returned to an 

environmentally compatible recycling facility

-  symbol 

@

 will remind you of this when the need for 

disposing occurs

DECLARATION OF CONFORMITY 

•  We declare under our sole responsibility that the product 

described under “Technical data” is in conformity with the 

following standards or standardization documents: EN 

60335, EN 61000, EN 55014 in accordance with the 

provisions of the directives 2006/95/EC, 2004/108/EC, 

2006/42/EC, 2000/14/EC, 2011/65/EU

• 

Technical file at

: SKIL Europe BV (PT-SEU/ENG1), 

4825 BD Breda, NL

¹ÊÁÂÆιƼ½ÊÇǾ¼½Æ

ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿

ÍÊÇȽƓˁ˅ʿ˂ ʽ¼¹Ɠ

Ĺ¾ ÁÂÿʹ¹¾

ÈÈÊÇιĹƹ¿½Ê

26.02.2014 

10

NOISE/VIBRATION

•  Measured in accordance with EN 60704-1 the sound 

pressure level of this tool is 81dB(A) and the sound 

power level 93 dB(A) (standard deviation: 3 dB), and the 

vibration 2.5 m/s² (hand-arm method; uncertainty 

K = 1.5 m/s²)

•  Measured in accordance with 2000/14/EC the 

guaranteed sound power level LWA is lower than 97 

dB(A) (conformity assessment procedure according to 

Annex V)

•  The vibration emission level has been measured in 

accordance with a standardised test given in EN/ISO 

5349; it may be used to compare one tool with another 

and as a preliminary assessment of exposure to vibration 

when using the tool for the applications mentioned

-  using the tool for different applications, or with different 

or poorly maintained accessories, may significantly 

increase

 the exposure level

-  the times when the tool is switched off or when it is 

running but not actually doing the job, may significantly 

reduce

 the exposure level

!  protect yourself against the effects of vibration 

by maintaining the tool and its accessories, 

keeping your hands warm, and organizing your 

work patterns