Oleo-Mac PW 115 C 6850-9091 - Инструкция по эксплуатации - Страница 20

20

GB

IMPORTANT: 

Only clean or filtered water should 

be used for intake. The delivery of the water 

intake tap should be equal to the double of the 

maximum pump range. 

Place the cleaner as close to the water supply 

system as possible.

Failure to comply with the above conditions 

causes serious mechanical damage to the 

pump and the loss of warranty cover.

Water supply from the potable water mains 

·  Connect a supply hose (not included) to the 

water inlet of the unit and to the water supply.

·  Open the tap.

Water supply from an open container

·  Unscrew the coupling part for the water inlet.

·  Screw the suction hose with filter (not included) 

onto the water connection of the unit.

·  Hang the filter in the container.

·  Vent the unit before operation.

·  Unscrew the high-pressure line at the high pres-

sure outlet of the unit.

·  Switch on the unit and let it run until water free 

of bubbles emerges at the high-pressure outlet.

·  Switch off the unit and screw on the highpressu-

re hose again.

>  

ELECTRICITY SUPPLY

-  The electrical connection of the appliance must 

be carried out by a QUALIFIED 

ELECTRICIST and conform to the norm IEC 60364-

1.

WARNING:

 Before connecting the appliance, 

make sure that the nameplate data are the same 

as those of the electrical mains and that the so-

cket is protected by a differential security breaker 

with tripping sensitivity below 

0.03 A - 30 ms.

-  If the appliance’s plug is not compatible with the 

socket, have the socket replaced with another of 

suitable type by professionally qualified staff.

-  Never use the appliance in ambient temperatu-

res below 0° C if it is equipped with a PVC 

(H VV-F) cable.

WARNING:

 Inadequate extension cords can be 

dangerous. If an extension cord is used, it must 

be suitable for outdoor use connections must be 

dry, away from the ground and a cable reel must 

be used so that the socket is at a distance of at 

least 60 mm from the ground.

<16 A

<25 A

<20 m 

ø 1,5 mm

2

14 AWG

ø 2,5 mm

2

12 AWG

20 m - 50 m ø 2,5 mm

2

12 AWG

ø 4,0 mm

2

10 AWG

IMPORTANT:

 The Total Stop device, which stops 

the machine during the bypass phase. To start 

the water cleaner, it is therefore necessary to set 

the switch on position (I)“ON”; after that press the 

pistol trigger. The Total Stop System will start the 

machine and will stop it automatically when the 

trigger is released. It is advisable to put on the 

safety of the pistol trigger whenever the machine 

is stopped, in order to avoid unintentional 

starting.

·  Any automatic start of the machine 

without pressing the gun trigger is 

attributable to air bubbles in the water 

or other similar phenomena which do not 

imply the existence of any defects in the 

machine. 

·  Do not leave the appliance unattended 

during the standby for more than 5 

minutes. Contrarily, for the safety of the 

appliance it is necessary to re-turn the 

switch into the (0) OFF position.

·  Please check that the coupling of the high 

pressure hose with the appliance and the 

gun supplied as standard equipment made 

correctly, that is to say without any water 

leak.

SWITCHING OFF

  See fig. 

C

CARE AND MAINTENANCE

  See fig. 

G

 WARNING:

 machine shall be disconnected from 

its power source, by removing the plug from the 

socket-outlet, after finishing work and during 

cleaning.

WARNING:

 Do not spray the appliance with 

water and do not use detergents or aggressive 

solvents. Machine could be damaged.