Remington HC9700 - Инструкция по эксплуатации

HC9700

Use and Care Guide

When using an electrical appliance, basic precautions should always be observed, 

including the following; read all instructions before using this appliance.

DANGER

To reduce the risk of electric shock:

•

Do not use in area that can be dropped into a sink or bath.

•  Make sure the charging stand, power adapter, and cord do not get wet. Do not 

plug or unplug the appliance with wet hands.

•  Do not reach for an appliance that has fallen into water. Unplug it immediately.
•  Do not use while bathing or in the shower.
•  Do not place or store this appliance where it can fall or be pulled into a tub  

or sink.

•  Except when charging, always unplug this appliance from the electrical outlet 

immediately after using. 

•  Unplug this appliance before cleaning it.

WARNING

To reduce the risk of burns, fire, electric shock or injury to persons:

•  This appliance is for household use only.
•  An appliance should never be left unattended when it’s plugged in, except 

when charging a rechargeable appliance.

•  Close supervision is necessary when this appliance is used by, on, or near 

children or persons with special needs.

•  Use this appliance only for its intended use as described in this manual. 
•  Do not use attachments not recommended by the manufacturer.
•  Keep the cord away from heated surfaces.
•  Never operate this appliance if it has a damaged cord or plug, if it is not 

working properly, if it has been dropped or damaged, or if it has been dropped 

into water. 

•  Never drop or insert any object into any of the appliance’s openings.
•  Do not use outdoors or operate where aerosol (spray) products are being used, 

or where oxygen is being administered.

IMPORTANT SAFETY 

INSTRUCTIONS

SAVE THESE INSTRUCTIONS

•  Make sure the cord is disconnected from the clipper while storing this appli-

ance and cord in a moisture-free area. Do not store it in temperatures exceed-

ing 140°F (60°C).

•  Do not use this appliance with a damaged or broken cutter unit, as injury may 

occur. Always make sure blades are aligned properly.

•  Always attach plug to appliance and then the adapter to the outlet. To discon-

nect, turn all controls to OFF, then remove adapter from outlet, then detach 

power cord from the dipper for storage.

•  Do not use an extension cord or a voltage converter with this appliance.
•  Do not wrap the cord around the appliance.
•  Dispose of batteries properly. Do not incinerate. Batteries may explode if  

overheated. Do not wrap in metal or aluminum foil. Wrap in newspaper before 

discarding. It is suggested that you contact local battery redemption site(s) in 

your area.

Remington

®

 hair clippers provide a quick and easy way to create 

professional-looking haircuts. Developed to combine professional grade blades with 

premium guide combs, this hair clipper enables you to achieve customized, modern 

looks and traditional hairstyles. To help you create those styles, and to extend the 

life of your hair clipper, please read all instructions before using.

 Product Features

Register Your New Product Today!

By registering your new Remington

®

 product, you will receive these important benefits:

Proof of Ownership • Product Protection • Product Registration • Special Offers

Register online at: RemingtonProducts.com

 Charging Your Appliance

Ultimate Performance Hair Clipper

4

6

8

1

2

3

7

Note: C

harge your appliance for a full 4 hours before using for the first time. 

•  Please refer to the charge times shown in this book.

•  Ensure the product is switched off.

•   The adaptor automatically adjusts to a main voltage between 100V and 240V.

•  Connect the product to the adaptor and then to the power outlet.

CHARGING VIA CHARGING STAND

•  Connect the adaptor to the charge stand and then to the power outlet.

•  Place the charge stand on a flat surface.

•   To charge the clipper without the charge stand connect the adaptor to the 

power port at the base of the product and then to the power outlet.

CHARGE LEVEL INDICATORS DURING CHARGING

Charge Level

Indicator

Charging

Red LED will blink slowly

Low Battery

Red LED will blink fast

Fully Charged

Red LED will stay solid 

(when plugged in)

•  Run time from fully charged is 150 mins. 

•  Charge time from empty is 4 hours.

Note: 

This product can be used corded or cordless.

Note:

  To preserve the life of your batteries, let them run out every 6 months then 

fully charge.

Note: 

When the battery is becoming depleted, the low battery indicator will flash.

QUICK CHARGE FUNCTION (TYPICAL EXPECTED RUN TIME)

Charge

Run Time

5 minutes

2.5 minutes

10 minutes

5 minutes

30 minutes

15 minutes

60 minutes

30 minutes

120 minutes

60 minutes

•  For corded use connect the product to the adaptor, then to the power outlet.

•  Extended corded only use will result in a reduction of battery life.

•   Cordless use – when the product is switched on and fully charged it can 

be used in cordless mode for up to 150 minutes.

•  Switch the product on by sliding up the on/off switch.

BEFORE STARTING THE CUT

•  Inspect the clipper making sure that it is free from hair and dirt.

•  Seat the person so that their head is approximately at your eye level.

•  Before cutting, always comb the hair so it is tangle free and dry.

•   1mm length is achieved without any combs. Holding the blades perpendicular 

to the skin will trim to 0.5mm at the lowest taper lever setting.

Guide Comb

Grade/Cut Length

0

#0, 1.5mm

1

#1, 3mm

2

#2, 6mm

3

#3, 9mm

4

#4, 12mm

5

#5, 16mm

6

#6, 19mm

7

#7, 22mm

8

#8, 25mm

 How to Use

TAPER LEVER

•  The taper lever settings can be seen on the table below.

•  Setting one gives you the length indicated on the fixed comb you are using.

•  Using the taper lever will increase this length correspondingly.

Setting

Cut length

1

1.0mm

2

1.15mm

3

1.3mm

4

1.45mm

5

1.6mm

TO ATTACH AND REMOVE A COMB

•  Make sure the blade is locked into place.

•  Install the desired comb attachment on the blade, it will latch into place.

•  To remove, pull the removal tab first to release the latch and pull away.

INSTRUCTIONS FOR CUTTING HAIR

•   For even cutting, allow the comb attachment/blade to cut its way through the 

hair. Do not force it through quickly. If you are cutting for the first time, start 

with the maximum comb attachment. 

STEP 1 – Nape of the neck 

•  Attach the 3mm or 6mm guide comb.

•   Hold the clipper with the blade teeth pointing upwards. Begin starting at the 

centre of the head at the base of the neck.

•   Slowly lift the clipper, working upwards and outwards through the hair, 

trimming just a little at a time.

STEP 2 – Back of the head

•   With the 12mm or 19mm guide comb on the clipper, cut the hair at the back of 

the head.

STEP 3 – Side of the head 

•  With the 3mm or 6mm guide comb on the clipper, trim sideburns.  

•   Then change to the longer 9mm guide comb and continue to cut the top of the head.

5

  1  On/off switch
  2  Taper lever
  3  Blade set
  4  Left and right ear guide combs
  5  9 guide combs (1.5mm –25mm)
  6  Charging stand

  7  Charge/low battery indicator
  8  Oil bottle
  9  Adaptor (not shown)
 10  Hex wrench (not shown)
 11  Angled cleaning brush (not shown)
 12  Blade release button (not shown)