VITEK WX-4001 MS - Инструкция по эксплуатации - Страница 5

ENGLISH

5

3.  Insert 8 “C” (UM 2) 1,5 V batteries (not sup-

plied) into the battery compartment following 
the polarity. 

4.  Close the battery compartment lid.

Attention! 

Battery leakage can lead to damages 

of the unit. To avoid damages of batteries follow 
the instructions below:
-   place the batteries properly.
-   take the batteries out if you are not going to 

use the unit for a long time.

-   do  not  recharge  the  batteries,  do  not  dis-

mantle them, and do not subject them to high 
temperature.

-   replace the batteries in time.

Note: 
When the unit is in the standby mode, it still 
consumes power, to switch off the unit com-
pletely disconnect the power cord from the 
socket. 

BASIC FUNCTIONS
Adjusting volume

Use the VOLUME knob (1) to adjust the desired 
volume level.

Increasing bass

Press the BASS (22) button to amplify low fre-
quency sound, the indicator (16) will light up. 

Radio stations reception

1.  Set the 

FUNCTION 

(4) switch to the RADIO 

position. 

2.  Select the desired band: FM ST., FM or AM, 

by setting the 

BAND 

(7) switch to the corre-

sponding position.

When tuning to the station, which transmits 
stereo signal, the FM ST (15) indicator will 
light up.

3.  Rotate the 

TUNING 

(10) knob to select the 

desired radio station. 

4.  After you stop listening to the radio, set the 

FUNCTION

 (4) switch to the TAPE(OFF) po-

sition.

Antenna

For the best FM reception, completely extend 
the FM ANTENNA and direct it at the desired 
angle. 
For the best AM reception try different variants 
of the unit location.

Playback of CD discs

Loading – open the CD compartment lid. Insert 
a CD disc and close the CD compartment lid.
Ejecting – after the playback stops open the CD 
compartment lid and eject the disc. Put the disc 
in the case for storage.
Always close the CD compartment lid in order 
to prevent it from dust.  Always eject a disc from 
the CD compartment if it is not being played 
back. 
1.  Plug the unit.
2.  Select the CD playback mode. To do it, set 

the 

FUNCTION

 (4) switch to the MP3(AUX) 

position. 

3.  If there is no disc in the disc slot or if the disc 

is damaged, the “---“symbols will appear on 
the LCD-display.

4.  Open the disc slot. Insert a disc and close 

the disc slot. Make sure that the disc is set 
properly – with the label upwards. 

5.  Total number of tracks will appear on the 

display.  

Note: This unit can playback CD-R and CD-
RW discs

Playback

In the stop mode, press the 

PLAY/PAUSE

 but-

ton, the disc will start playing back and 
the number of the track and “PLAY” will appear 
on the display.

Pause

To pause the playback, press the 

PLAY/PAUSE

button in the playback mode, “Play” will start 
flashing on the LCD-display.
To resume the playback, press the 

PLAY/

PAUSE

 button once again

Stop playback

To stop the playback, press the 

STOP 



button. 

Total number of tracks will appear on the LCD-
display.

Moving to the beginning of the track, to the 
previous and the next track

1.  To move to the beginning of the played back 

track press the 



 button once in the play-

back mode.

2.  To move to the next track, press the 



 but-

ton once.

3.  To move to the previous track, press the 



button twice in the playback mode.

4001Instruk_ital.indd   5

15.11.2011   14:09:00