Einhell TC-SS 405 E - Инструкция по эксплуатации - Страница 19

Лобзики Einhell TC-SS 405 E - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.

Если остались вопросы, задайте их в комментариях после инструкции.

"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Страница:
/ 88
Загружаем инструкцию
background image

GB

- 19 -

6. Operation

 6.1 Please note:

• 

Your saw does not cut wood automatically. 

For cutting to occur, you have to guide the 

wood  against the blade.

• 

The teeth cut only on the down stroke of the  

blade.

• 

You have to guide the wood slowly against 

the blade because the teeth are very small.

• 

Every new user needs a certain training 

period.  You are certain to break a number of 

blades at the beginning.

• 

When cutting thick timber, be particularly 

careful not to bend or twist the blade. This will 

help to prolong blade life.

6.2 On/O

  switch (Fig. 3 / Item 2)

• 

Press the green button to switch the saw on.

• 

Press the red button to switch the machine 

off.

• 

Please note: The machine is equipped with a 

safety switch to prevent it being switched on 

again accidentally after a power failure.

6.3  Blade speed regulator (3)

The blade speed regulator allows you to set the  

blade speed appropriate to the material to be cut.

6.4 Carrying out internal cuts

1.  A feature of this fretsaw is that it allows you to  

carry out internal cuts in a panel without  

damaging it on the outside or circumference.

Warning! To avoid injury from accidental star-

ting: Before you remove or change the blade, 

always set the switch to „0“ position and pull 

the power plug out of the socket.

2.  To carry out internal cuts in a panel: Remove 

the blade as described in Section 5.3.2

3.  Drill a hole in the panel in question.

4.  Place the panel on the saw table with the 

drilled hole above the access hole.

5.  Install the blade through the hole in the panel 

and adjust the blade tension.

6.  When you have completed the internal cuts,  

remove the blade from the blade holders (as  

described in Section 5.3.2) and take the pa-

nel o

  the table.

6.5  Adapter for jigsaw blades (Fig. 8/9)

• 

Remove the saw blade as described in 5.3.2.

• 

Now insert the fretsaw blade (a) in the adap-

ter.

• 

First remove the table insert (18).

• 

Then hook both adapters (22) on the two saw  

blade holders (8/13).

• 

Insert the saw blade as described in 5.3.2.

7.  Cleaning, maintenance and 

ordering of spare parts

Always pull out the mains power plug before star-

ting any cleaning work.

7.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could 

attack the plastic parts of the equipment. En-

sure that no water can seep into the device.

 7.2 Bearings

Lubricate the bearings of the guide rollers periodi-

cally with high-grade machine grease, but at least 

after every 25-30 hours in operation.

7.3 Carbon brushes

In case of excessive sparking, have the carbon  

brushes checked only by a quali

fi

 ed electrician.

Important! The carbon brushes should not be rep 

laced by anyone but a quali

fi

 ed electrician.

7.4 Maintenance

There are no parts inside the equipment which  

require additional maintenance.

Anleitung_BT-SS_405_E_SPK1.indb   19

Anleitung_BT-SS_405_E_SPK1.indb   19

04.10.11   08:17

04.10.11   08:17

Характеристики

Оцените статью
tehnopanorama.ru
Остались вопросы?

Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)

Задать вопрос

Часто задаваемые вопросы
Как посмотреть инструкцию к Einhell TC-SS 405 E?
Необходимо подождать полной загрузки инструкции в сером окне на данной странице
Руководство на русском языке?
Все наши руководства представлены на русском языке или схематично, поэтому вы без труда сможете разобраться с вашей моделью
Как скопировать текст из PDF?
Чтобы скопировать текст со страницы инструкции воспользуйтесь вкладкой "HTML"