Bosch GST 150 CE (0601512000) - Инструкция по эксплуатации - Страница 10

10

 | English 

2 609 932 936 | (16.4.14)

Bosch Power Tools

Safety Warnings for Jigsaws



Hold power tool by insulated gripping surfaces, when 
performing an operation where the cutting accessory 
may contact hidden wiring or its own cord. 

Cutting ac-

cessory contacting a “live” wire may make exposed metal 
parts of the power tool “live” and could give the operator an 
electric shock.

Additional Safety and Working 
Instructions



Keep hands away from the sawing range. Do not reach 
under the workpiece. 

Contact with the saw blade can 

lead to injuries.



Apply the machine to the workpiece only when 
switched on. 

Otherwise there is danger of kickback when 

the cutting tool jams in the workpiece.



Pay attention that the base plate rests securely on the 
material while sawing. 

A jammed saw blade can break or 

lead to kickback.



When the cut is completed, switch off the machine and 
then pull the saw blade out of the cut only after it has 
come to a standstill. 

In this manner you can avoid kick-

back and can place down the machine securely.



Use only undamaged saw blades that are in perfect con-
dition. 

Bent or dull saw blades can break, negatively influ-

ence the cut, or lead to kickback.



Do not brake the saw blade to a stop by applying side 
pressure after switching off. 

The saw blade can be dam-

aged, break or cause kickback.



Use suitable detectors to determine if utility lines are 
hidden in the work area or call the local utility company 
for assistance. 

Contact with electric lines can lead to fire 

and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or 
may cause an electric shock.



Secure the workpiece. 

A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.



Always wait until the machine has come to a complete 
stop before placing it down. 

The tool insert can jam and 

lead to loss of control over the power tool.



Before any work on the machine itself, pull the mains 
plug.



The saw blade should not be longer than required for 
the intended cut. Use a narrow saw blade when sawing 
tight curves.



Check the tight seating of the saw blade. 

A loose saw 

blade can fall out and lead to injuries.



When ejecting the saw blade, hold the machine in such 
a manner that no persons or animals can be injured by 
the ejected saw blade.



Dusts from materials such as lead-containing coatings, 
some wood types, minerals and metal can be harmful to 
one’s health and cause allergic reactions, lead to res-
piratory infections and/or cancer.

 Materials containing 

asbestos may only be worked by specialists.

–

As far as possible, use a dust extraction system suitable 
for the material.

–

Provide for good ventilation of the working place.

–

It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the 
materials to be worked.



Prevent dust accumulation at the workplace. 

Dusts can 

easily ignite.



Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the 
nameplate of the machine. Power tools marked with 
230 V can also be operated with 220 V.



To save energy, only switch the power tool on when using 
it.



The contact protector attached to the casing (see fig-
ure 15, page 192) prevents accidental touching of the 
saw blade during the working procedure and may not 
be removed.



Before sawing in wood, particle boards, building mate-
rials etc., check for foreign objects, such as nails, 
screws, etc. and remove them as required.



Plunge cuts may only be applied to soft materials, such 
as wood, gypsum board, etc. For plunge cuts, use only 
short saw blades.



The sliding shoe can prevent the surface from being 
scratched. The splinter guard can prevent fraying of 
the surface while sawing wood. Do not use the splinter 
guard for mitre cuts.



Adapt the settings of your power tool to the respective 
application. For example, reduce the stroke rate and 
orbital action when cutting metal or for tight curved 
cuts.



When working small or thin work pieces, always use a 
sturdy support or a saw table (accessory).



In extreme conditions, always use dust extraction as 
far as possible. Blow out ventilation slots frequently 
and install a residual current device (RCD). 

When work-

ing metals, conductive dust can settle in the interior of the 
power tool. The total insulation of the power tool can be im-
paired.



Products sold in GB only

: Your product is fitted with a 

BS 1363/A approved electric plug with internal fuse 
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should 
be cut off and an appropriate plug fitted in its place by an 
authorised customer service agent. The replacement plug 
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains 
socket elsewhere.

Products sold in AUS and NZ only

: Use a residual current 

device (RCD) with a rated residual current of 30 mA or 
less.

OBJ_BUCH-1027-003.book  Page 10  Wednesday, April 16, 2014  10:14 AM