Bosch GST 140 CE - Инструкция по эксплуатации - Страница 12

12

 | English 

2 609 932 772 | (29.3.11)

Bosch Power Tools

f

Always wait until the machine has come to 
a complete stop before placing it down. 

The 

tool insert can jam and lead to loss of control 
over the power tool.

f

Do not direct the light beam at persons or 
animals and do not stare into the light beam 
yourself (not even from a distance).

f

Check the tight seating of the saw blade. 

A loose saw blade can fall out and lead to in-
juries.

f

Use a narrow saw blade when sawing tight 
curves.

f

When ejecting the saw blade, hold the ma-
chine in such a manner that no persons or 
animals can be injured by the ejected saw 
blade.

f

Dusts from materials such as lead-contain-
ing coatings, some wood types, minerals 
and metal can be harmful to one’s health 
and cause allergic reactions, lead to respi-
ratory infections and/or cancer.

 Materials 

containing asbestos may only be worked by 
specialists.
– As far as possible, use a dust extraction 

system suitable for the material.

– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your 
country for the materials to be worked.

f

Prevent dust accumulation at the work-
place. 

Dusts can easily ignite.

f

Observe correct mains voltage! The voltage 
of the power source must agree with the 
voltage specified on the nameplate of the 
machine. Power tools marked with 230 V 
can also be operated with 220 V.

f

The restarting protection feature prevents 
uncontrolled restarting of the machine af-
ter an interruption in the power supply. 

To 

restart the operation

, switch the On/Off 

switch  to the Off position and start the ma-
chine again.

f

The contact protector attached to the casing 
(see figure 17, page 227) prevents acciden-
tal touching of the saw blade during the 
working procedure and may not be removed.

f

Before sawing in wood, particle boards, 
building materials etc., check for foreign 
objects, such as nails, screws, etc. and re-
move them as required.

f

Plunge cuts may only be applied to soft ma-
terials, such as wood, gypsum board, etc.

f

The metal overshoe prevents the plastic 
footplate from being scratched up, espe-
cially when sawing metal.

f

Adapt the settings of your power tool to the 
respective application. For example, reduce 
the stroke rate and orbital action when cut-
ting metal or for tight curved cuts.

f

When working small or thin work pieces, al-
ways use a sturdy support or a saw table 
(accessory).

f

In extreme conditions, always use dust ex-
traction as far as possible. Blow out ventila-
tion slots frequently and install a residual 
current device (RCD). 

When working metals, 

conductive dust can settle in the interior of 
the power tool. The total insulation of the 
power tool can be impaired.

f

Products sold in GB only

: Your product is fit-

ted with a BS 1363/A approved electric plug 
with internal fuse (ASTA approved to 
BS 1362).
If the plug is not suitable for your socket out-
lets, it should be cut off and an appropriate 
plug fitted in its place by an authorised cus-
tomer service agent. The replacement plug 
should have the same fuse rating as the orig-
inal plug.
The severed plug must be disposed of to 
avoid a possible shock hazard and should 
never be inserted into a mains socket else-
where.

Products sold in AUS and NZ only

: Use a re-

sidual current device (RCD) with a rated re-
sidual current of 30 mA or less.

Symbols

The following symbols are important for reading 
and understanding the operating instructions. 
Please take note of the symbols and their mean-
ing. The correct interpretation of the symbols 
will help you to use the machine in a better and 
safer manner.

OBJ_BUCH-1320-002.book  Page 12  Tuesday, March 29, 2011  12:39 PM