Einhell GC-CG 3,6/70 Li WT, 3.6В 2 Ач (3410365) - Инструкция по эксплуатации - Страница 17

GB

- 17 -

6.2  Using the equipment as shrub shears

Hold the shrub shears slightly tilted in the direc-

tion of the shrub you wish to cut. Start by cutting 

the sides of the shrub working from the bottom 

up, and 

fi

 nally cut the top of the shrub. The blade 

guard hood must be slid over the blade and the 

rechargeable battery removed when the equip-

ment is not being used.

• 

Shrubs which loose their leaves in the autumn 

should be cut in June and October.

• 

Evergreen shrubs should be cut in April and 

August.

6.2.1 Assembly

Since the equipment is supplied as grass shears 

(see section 6.1), the grass cutting blade has to 

be swapped over for the shrub cutter blade which 

is supplied with the product. 

Caution! 

Risk of 

injury.

Use protective gloves and the blade guard 

hood which is supplied with the equipment.

1.  Push the blade release mechanism (Fig. 5a) 

forward, press down on the upper section 

(Fig. 5b) and remove the blade at the same 

time (Fig. 5b).

2.  (Fig. 6) Slide the blade housing into the 

mount on the equipment housing.

Push the blade release mechanism forward 

again, press down on the upper section and 

press the blade into the lock at the same time. 

The drive unit on the equipment is now con-

nected to the blade.

3.  Remove the blade guard hood.

6.2.2 Switching on/o

ff

 .

Proceed as described in section 6.1.1.

7.  Cleaning, maintenance and 

ordering of spare parts

Danger!

7.1 Cleaning

• 

Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth. Do not use cleaning agents or solvents; 

these could attack the plastic parts of the 

equipment. Ensure that no water can seep 

into the device. The ingress of water into an 

electric tool increases the risk of an electric 

shock.

• 

The shears should be cleaned thoroughly 

every time before and after use. A few drops 

of oil (for example sewing machine oil) ap-

plied to the blades improve the cutting perfor-

mance. However, never apply grease to the 

blades.

• 

To guarantee a constant exact cut it is ne-

cessary that grass residues and dirt are also 

removed from the top and bottom blades.

7.2 Maintenance

• 

For good cutting performance the blades 

should always be sharp. They can be there-

fore be resharpened with a whetstone. In 

particular we recommend to remove notches 

and ridges which are produced on the blades 

by stones or the like.

• 

There are no other parts inside the equipment 

which require maintenance.

7.3  Ordering replacement parts:

Please quote the following data when ordering 

replacement parts:

• 

Type of machine

• 

Article number of the machine

• 

Identification number of the machine

• 

Replacement part number of the part required

For our latest prices and information please go to 

www.Einhell-Service.com

8.  Disposal and recycling

The unit is supplied in packaging to prevent its 

being damaged in transit. This packaging is raw 

material and can therefore be reused or can be 

returned to the raw material system.

The unit and its accessories are made of various 

types of material, such as metal and plastic. De-

fective components must be disposed of as spe-

cial waste. Ask your dealer or your local council.

Anl_GC_CG_3_6-70_Li_WT_SPK13.indb   17

Anl_GC_CG_3_6-70_Li_WT_SPK13.indb   17

21.06.2022   09:20:00

21.06.2022   09:20:00