Einhell GC-CG 3,6/70 Li WT, 3.6В 2 Ач (3410365) - Инструкция по эксплуатации - Страница 16

GB

- 16 -

Caution!

Residual risks

Even if you use this electric power tool in 

accordance with instructions, certain resi-

dual risks cannot be rules out. The following 

hazards may arise in connection with the 

equipment’s construction and layout:

1.  Cut injuries are possible if no safety clothing 

is used.

2.  Lung damage if no suitable protective dust 

mask is used.

3.  Damage to hearing if no suitable ear protec-

tion is used.

4.  Health damage caused by hand-arm vib-

rations if the equipment is used over a pro-

longed period or is not properly guided and 

maintained.

5.  Before starting the equipment

Charging the rechargeable battery

• 

 Connect the unit to the charger (Figure 3).

• 

 Check that your mains voltage is the same as 

that marked on the rating plate.

• 

 The time it takes to fully recharge an empty 

battery is approximately 3 to 5 hours. The 

temperature of the battery pack might rise 

slightly during the charging operation. This is 

normal.

Charging procedure

Plug the charger in a socket-outlet; a red LED 

(Fig. 3/Item A) lights up to indicate that charging is 

in progress. The battery pack is being charged.

Charging completed

The red LED (Fig. 3/Item A) goes out. A green 

LED lights up in its place (battery charged).

Battery does not charge up

If the battery fails to charge, please check

-  whether there is voltage at the socket outlet.

-  whether there is good contact at the charging 

contacts.

-  whether the red LED and the green LED (Fig. 

3/ Item A) light up at the same time. This can 

happen, for example, if the battery tempera-

ture becomes too low or too high. Place the 

unit in storage at room temperature for one 

day.

If you still fail to charge the battery pack, please 

return the complete tool together with the battery 

charger to our Customer Service Center.

To ensure that items are properly packaged 

and delivered when you send them to us, 

please contact our customer service or the 

point of sale at which the equipment was 

purchased.

When shipping or disposing of batteries and 

cordless tools, always ensure that they are 

packed individually in plastic bags to prevent 

short circuits and 

fi

 res.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly. 

You must recharge the battery pack when you 

notice that the performance of the device drops. 

Never allow the battery pack to become fully di-

scharged. This will cause it to develop a defect.

Warning! Any foreign bodies must be com-

pletely cleared away from the area to be 

worked on.

Warning!

The switching devices installed on the tool 

by the manufacturer are not allowed to be 

removed or bypassed, e.g. by 

fi

 tting a swit-

ching button to the handle, as this may result 

in risk of injury and the tool will no longer 

switch o

ff

  automatically.

6. Operation

 6.1  Using the equipment as grass shears

Allow the grass shears to glide over the ground. 

The best cutting performance is achieved on dry 

lawns.

The blade guard hood must be pushed over the 

blade when the unit is not being used.

The grass shears is supplied ready assembled.

(Fig. 4) Remove the blade guard hood (Item 6).

6.1.1 Switching on/o

ff

 .

1.  (Fig. 4) To switch on, press the safety lock-o

ff

(Item 3) and press the On/O

ff

  switch (Item 4) 

at the same time.

2.  To switch o

ff

 , let go of the On/O

ff

  switch.

Anl_GC_CG_3_6-70_Li_WT_SPK13.indb   16

Anl_GC_CG_3_6-70_Li_WT_SPK13.indb   16

21.06.2022   09:20:00

21.06.2022   09:20:00