Bort BFP-18A - Инструкция по эксплуатации - Страница 7

7

Cordless sprayer

THE NUMBERS MENTIONED IN THE TEXT 
CORRESPOND WITH THE PICTURE SAT PAGE2.

TECHNICALSPECIFICATIONS

Battery voltage / Capacity

18 V / 1.2 Ah

Maximum nozzle 

fl

 ow rate 

300 ml/min

Container capacity

500ml

Weight

1.9 kg

PRODUCT INFORMATION   

 A 

1. Motor housing
2. Output control
3. Triggerswitch
4. Handle
5. Paintcontainer
6.  Spray basket nozzle
7. Spare valve
8. Viscositycup

SAFETY INSTRUCTIONS

The following symbols are used in these instructions 
for use:

Denotes risk of persona! injury, loss of life or 
damage to the tool in case of non-obser-
vance of the instructions in this manual.

Carefully read this manual before using the machine. 
Make sure that you know how the machine functions 
and how to operate it. Maintain the machine in accord-
ance with the instructions to make sure it functions 
properly. Keep this manual and the enclosed documen-
tation with the machine.

ADDITIONAL SAFETY INSTRUCTIONS

-  NEVERSPRAY AT PERSONS- Neveraim the nozzle 

at another person or animal. Never allow the spray 
to come in to direct con tact with the skin.

  FLASH POINT - This spray gun must not be used for 

spraying 

fl

 ammable paints and solvents with a 

fl

 ash 

point of less than 32°C

  VENTILATION - Always make sure that there is ad-

equate ventilation in the work area when spraying.

-  BASKET NOZZLE - Always keep the spray basket 

nozzle in piace during use.

-  CONSIDER WORK AREA ENVIRONMENT - Do not 

use spray guns where there is a risk of 

fi

 re or explo-

sion.

-  BEWARE OF ANY HAZARD - Beware of any hazard 

by the material being sprayed and consult the mark-
ings on the container or the information supplied by 
the manufacturer.

-  DO NOT SPRAY-Do not spray any material where 

the hazard is notknown.

-  USE EYE PROTECTION - Always use appropriate 

eye protection to keep hazardous vapours or fumes 
out of the eyes.

-  WEAR A MASK - Never operate a spray gun without 

wearingaface mask.

-  PROTECT YOUR EARS - Wear ear protectors if the 

sound pressure exceeds 85 dB(A).

-  MAINTAIN YOUR TOOLS - Keep your spray gun, 

paint container and nozzles clean. Do not clean with 

fl

 ammable liquids with a 

fl

 ash point less than 32°C 

Inspect the mains lead periodically and if damaged 
have it replaced by a quali

fi

 ed person.

-  NAKED FLAMES - Never spray near a naked 

fl

 ame 

or appliance pilot

fl

 ame.

-  SMOKING - Never smoke whilst spraying. THIN-

NING - Always read the paint manufacturers thin-
ning recommendations or instructions before using 
paint or other materials.

•  SWITCH OFF WHEN NOT SPRAYING - Avoid run-

ning the unit with the 

fl

 ow rate knob fully closed for 

any length of time.

We accept no responsibility for damage caused by 
the use of unsuitable substances, or paints that hare 
not been thinned correctly, and any health hazards 
that arise from lack of adequate ventilation

OPERATION INSTRUCTIONS

PREPARATION   

 B 

Do not use textured wall paints or coatings as 
this wHIblock the nozzle.

To obtain the best results, it is important that you pre-
pare the surface to be sprayed and thin the paint to 
the correct viscosity, before you operate your spray 
gun. Always ensure that the surfaces to be sprayed 
are free from dust, dirt and grease. Make sure that you 
have masked the areas that should not be sprayed, 
using a good quality masking tape. The paint or 

fl

 uid 

to be sprayed should be thoroughly mixed and free 
from lumps or other particles. Many substances can 
be sprayed with your spray gun, but always check the 
manufacturers recommendations before purchasingy-
our paint.

THINNING

Always remember to disconnect from the 

mains sup-ply before 

fi

 lling the paint contain-

er with sprayable material.

Most paints are supplied ready for brush application 
and will need to be thinned before they are suitable to 
be sprayed. Follow the manufacturers advice on thin-
ning the paint when used with a spray gun. The viscos-
ity cup will help you to determine the correct viscosity of 
paint to be used. To determine the correct viscosity, 

fi

 ll 

the cup to the brim with the paint. Measure the amount 
of time it takes for the cup to empty back into the can. 
The table below shows recommended times for differ-
ent types of material.

English