Компрессоры Einhell X-Change PRESSITO 18/21 Kit (4020467K) - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
GB
- 24 -
•
Switch in the middle: OFF
•
Switch to the right: Low-pressure operation
6.2 Compressor compressed air operation
(Fig. 1a, 1b, 2, 7)
•
To inflate objects with compressed air, use
the compressed air hose (5).
•
Connect the adapter of the compressed air
hose to the object you wish to inflate.
•
Depending on what you are inflating, also use
the adapters (7, 8, 9) or other adapters availa-
ble from retail stores.
•
The pressure at the compressed air hose will
be displayed in the display (11).
•
The unit of the displayed pressure can be se-
lected with the button (15). The pressure can
be displayed in units of [bar], [PSI] or [kPa].
•
The button (14) allows the desired pressure
to be reduced.
•
The button (16) allows the desired pressure
to be increased.
•
Switch on the equipment by moving the se-
lector switch (12) to the compressed air ope-
ration position (see 6.1.).
•
The compressor will then pump until the pre-
set pressure on the display is reached, then it
will switch off.
•
Warning! Observe the information supplied
by the tire manufacturer and the vehicle ma-
nufacturer relating to the recommended tire
pressure.
•
Warning! This equipment is not calibrated!
For a calibrated measurement value, check
the actual tire pressure using a calibrated me-
ter after you have inflated the tires yourself,
e.g. at a petrol station.
•
Just before it is switched off, the pressure
which is shown in the display can be 0.05 –
0.2 bar higher than the preselected pressure,
because of overpressure in the air hose.
•
Allow the compressor to cool down for about
5 minutes after every 5 minutes of operation
in order to prevent overheating.
6.3 Low-pressure blower operation
(Fig. 1a, 3, 4)
6.3.1 Suctioning air (Fig. 3, 7)
•
To suction out objects with a large volume
until they are empty (e.g. deflating an air
mattress, etc.), connect the air hose (3) to the
extractor connection (13).
•
Connect the air hose to the object you wish
to deflate.
•
Switch on the equipment by moving the se-
lector switch (15) to the low-pressure operati-
on position (see 6.1.).
•
Switch off the equipment once the object has
been sufficiently deflated.
6.3.2 In
fl
ating (Fig. 4, 7)
Warning! When using the equipment to in
fl
ate
objects, check the information and safety instruc-
tions provided by the manufacturer.
•
To inflate objects with a large volume (e.g.
inflating an air mattress, etc.), connect the air
hose (3) to the inflating connection (4).
•
Connect the air hose to the object you wish
to inflate.
•
Switch on the equipment by moving the se-
lector switch (12) to the low-pressure operati-
on position (see 6.1.).
•
Switch off the equipment once the object has
been sufficiently inflated.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
Anl_PRESSITO_SPK9.indb 24
Anl_PRESSITO_SPK9.indb 24
01.09.2017 11:02:18
01.09.2017 11:02:18
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
