Einhell X-Change PRESSITO 18/21 Kit (4020467K) - Инструкция по эксплуатации - Страница 23

GB

- 23 -

5.  Before using the equipment

Before you connect the equipment to the power 

supply make sure that the data on the rating plate 

are identical to the supply voltage (if operating 

from the mains power supply).

Before you connect the equipment to the power 

supply make sure that the data on the rating pla-

te are identical to the data for the rechargeable 

battery (if using a rechargeable battery for ope-

ration).

• 

Check the equipment for damage which may 

have occurred in transit. Report any damage 

immediately to the transport company which 

was used to deliver the compressor.

• 

Make sure that the intake air is dry and dust-

free.

• 

Do not install the compressor in a damp or 

wet room.

• 

The compressor may only be used in suitable 

rooms (with good ventilation and an ambient 

temperature from +5 °C to 40 °C). There must 

be no dust, acids, vapors, explosive gases or 

inflammable gases in the room.

• 

The compressor is designed to be used in dry 

rooms. It is prohibited to use the compressor 

in areas where work is conducted with spray-

ed water.

• 

Operate the equipment only on a firm, level 

surface.

Warning!

 When using the equipment to in

fl

 ate 

objects, check the information and safety instruc-

tions provided by the manufacturer.

5.1  Charging the LI battery pack (Fig. 2, 9)

1.  Remove the battery pack (6) from the handle, 

pressing the pushlock button (a) downwards 

to do so.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(d) into the socket outlet. The green LED will 

then begin to 

fl

 ash.

3.  Push the battery pack (6) onto the battery 

charger (d).

In section 10 (Charger indicator) you will 

fi

 nd a 

table with an explanation of the LED indicator on 

the charger.

If the battery pack fails to charge, check for the 

following:

• 

voltage at the power socket

• 

whether there is good contact at the charging 

contacts of the charging unit.

If the battery pack still fails to charge, send

• 

the charger and charging adapter

• 

and the battery pack

to our customer service center.

5.2 Battery capacity indicator (Fig. 2)

Press the button for the battery capacity indicator 

(b). The battery capacity indicator (c) will indicate 

the charge status of the battery by means of 3 

LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED blinks:

The battery is empty, recharge the battery.

All LEDs 

fl

 ash:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a 

defective battery pack.

6. Operation

6.1 Changing between mains/battery operati-

on and compressor compressed air/low-

pressure blower operation (Fig. 7)

To change over between mains-powered and 

battery-powered operation, press the selector 

switch (10):

• 

DC/switch to the right:

• 

The equipment will be supplied with power 

from the rechargeable battery.

• 

AC/switch to the left:

• 

The equipment will be supplied with power 

from the power cable.

• 

To change over between compressed air and 

low-pressure operation, press the selector 

switch (12):

• 

Switch to the left: Compressed air operation

Anl_PRESSITO_SPK9.indb   23

Anl_PRESSITO_SPK9.indb   23

01.09.2017   11:02:18

01.09.2017   11:02:18