Bort BLK-252-Lt - Инструкция по эксплуатации - Страница 5

5

Car compressor

Intended Use

This product is used for inflation of tires, balls, inflatable 
air beds, bicycle tires, etc. The car compressor is equipped 
with a manometer and an adaptor for connection to the 
car cigarette lighter.

Technical specifications

Car system voltage, V

12

Power, W

120

Discharge, litres per min.

25

Idling speed, rpm

3400

Maximum output pressure, 
bar (Pa)

7 (700000)

Weight, kg

1,8

GENERAL REQUIREMENTS

•  Do not leave the car compressor in the rain and snow.
•  Do not use the product in highly humid environment.
•  Do not work near inflammable liquids and gases.
•  Do not let children operate the car compressor.
•  Keep in a dry and closed place out of reach of children.
•  Do not overload the product. Failures caused by over-

load are not covered by conditions of free warranty 
repair.

•  Use only for the purpose specified.
•  Control operability of the air hose.
•  It is prohibited to move the compressor holding it by the 

power cable.

•  Avoid contact of the hose with oil and sharp objects.
•  Avoid overheating of the hose.
•  Keep your balance while working.
•  Keep the compressor clean. Clean it regularly from oil 

stains.

•  Disconnect the compressor from the car system voltage 

in the following cases:
- The product is not in use.
- During maintenance operations.
- During replacement of parts and mechanical units.

•  Be attentive and collected while working.
•  Refrain from work, if you are tired or ill.
•  Regularly check the product for damages and failures.
•  If any defects are detected, contact the service center
•  For failure avoidance, do not use spare parts of other 

manufacturers.

To prevent failures

•  Keep the compressor adapter clean. With the compres-

sor connected to the car cigarette lighter, in case of 
short circuit, a life-threatening situation may occur. Ac-
cumulator capacity is very high, so you can get injured.

•  Protect the compressor from overheating. Do not cover 

the compressor with foreign objects while in use.

Before connecting, please check

•  If the adapter and the car lighter socket match;
•  If the car accumulator voltage matches with the com-

pressor’s characteristics;

•  If the accumulator can provide 10 A;
•  Absence of failures and breakdowns in the cable and the 

adapter for the cigarette lighter.

OPERATION

•  First, check pressure in the inflated object. It can be 

done with the manometer, installed in the compressor. 
Just connect the hose of the idle compressor to the 
inflated object.

•  Avoid excessive pressurization.
•  Do not place the working compressor in the car com-

partment.

•  Do not leave the working compressor unattended.
•  Switch off the compressor immediately in the following 

cases: 
1. If the adapter or power cable is damaged;
2. Smell of burning insulation appears.

ATTENTION!

 This compressor is intended for short-time 

operation (not more than 10 minutes). Longer operation 
of the compressor may cause its overheating and break-
down. If you need to use the compressor longer, after first 
10 minutes switch off the device and let it cool down for 
10 minutes before restart.

Inflation of car tires

•  Place the car to ensure the lowest position of the tire 

valve.

•  Connect the nipple to the tire valve. Push the lever 

down and fix the nipple.

•  Check pressure with the manometer.
•  Connect the compressor to the car lighter socket. 
•  When the required pressure level is reached, disconnect 

the compressor from the car lighter socket. 

•  Release the lock of the joining nipple and remove it 

from the valve.

Inflation of balls and toys

•  Install the valve adapter (connector or needle for ball 

inflation) on the nipple and latch the lock by pushing 
the lever down.

•  Connect the air hose with the adapter to the inflated 

object.

•  Connect the compressor to the car lighter socket. 
•  Turn the compressor on. 
•  When the required pressure level is reached, disconnect 

the compressor from the car lighter socket. 

•  Disconnect the air hose with the adapter from the in-

flated object.

•  Quickly close the air passage of the inflated object.

ATTENTION!

 Control air pressure in the inflated object. 

Avoid excessive pressurization of the inflated object. 

English