Philips HD8425 Saeco Poemia - Инструкция по эксплуатации - Страница 8

• 8 •

4 INSTALLATION

For your own and other people safety, carefully follow 
the "Safety Regulations" indicated in chapter 3.

4.1 Packaging

The original packaging has been designed and manufactured 
to protect the machine during transport. We recommend 
keeping the packaging material for possible future transport.

4.2 Installation 

Precautions

Before installing the machine, read the following safety pre-
cautions carefully:
•  Place the machine in a safe place.
•  Make sure children cannot play with the machine.
•  Do not place the machine on hot surfaces or near open 

fl ames.

The coff ee machine is now ready to be connected to the electric 
network.

Note: we recommend washing the components 
before using them for the fi rst time and/or af-

ter they have not been used for a certain period of time.

4.3 Machine 

Connection

Electric  power  may  be  very  dangerous!  It  is 
therefore necessary to strictly follow the safety 

regulations. Do not use faulty power cords. Faulty cords 
and plugs must be replaced immediately by Authorised 
Service Centres.

The voltage of the appliance has been pre-set by the manu-
facturer. Check that the voltage matches the indication on the 
data plate at the bottom of the appliance.

•  Insert the plug into a wall socket with suitable power volt-

age.

4.4 Water 

tank

• 

(Fig.1A) - 

Remove the lid from the water tank (2) by lifting 

it.

• 

(Fig.1B) - 

Remove the water tank (5).

• 

(Fig.2) - 

Rinse it and fi ll it with fresh drinking water: do 

not exceed the (MAX) level indicated in the water tank.

Fill  the  tank  only  with  fresh,  non-sparkling, 
drinking water. Hot water or any other liquid 

may damage the tank. Do not operate the machine 

without water: make sure that there is enough water 
in the tank.

• 

(Fig.3A) - 

Insert  the  water  tank  making  sure  that  it  has 

been properly repositioned in its former seat and then 
reposition the lid (2).

Make  sure  that  the  tank  is  fully  inserted  in  the 
machine by pressing it gently up to its limit stop 

(THE REFERENCE MARK SHOWN IN FIG.3B SHOULD BE 
COMPLETELY VISIBLE). This is to avoid water leaks from 
its bottom.

4.5 Circuit 

Priming

At the beginning, after dispensing steam or when the water 
tank is empty, the machine’s water circuit must be primed. 
•  Press the ON/OFF button (11); the light (18) will turn on to 

indicate that the machine is on.

• 

(Fig.4) - 

Place a container under the steam wand (Pan-

narello). 

•  Open the “hot water/steam” knob (3) by turning it coun-

ter-clockwise.

• 

(Fig.5) - 

Set the selection knob (17) to the "

" position.

•  Wait until a steady jet of water fl ows out of the steam 

wand (Pannarello).

• 

(Fig.5) - 

Set the selection knob (17) to the " " position.

•  Close the "hot water/steam" knob (3) by turning it clock-

wise. Remove the container.

4.6  Using the Machine for the First Time 

or After a Period of Inactivity

This simple operation ensures an optimum brewing and must 
be performed:
-  at fi rst start-up;
-  when the machine remains inactive for a long time (more 

than 2 weeks).

Dispensed  water  must  be  emptied  into  an  ad-
equate  drain.  It  is  not  suitable  for  food  use.  If 

the container fi lls up during the cycle, stop dispensing 
water and empty the container before resuming the 
operation.

• 

(Fig.2) - 

Rinse the tank and fi ll it again with fresh drinking 

water.

• (Fig.4) 

- 

Place a container under the steam wand (Pan-

narello). Open the knob (3) by turning it counter-clockwise.

(Fig.5) - 

Set the selection knob (17) to the "

" position.

•  Dispense the whole water tank content from the steam/

hot water wand (Pannarello). To end the operation, set the 
selection knob (17) to the " " position and close the knob