VITEK VT-1508 R - Инструкция по эксплуатации - Страница 5

5

       ENGLISH         

5

• Press the power ON/OFF button (14). 

The indicator (13) will be lighted. The in-
dicator (12) keeps blinking until required 
temperature is reached. Afterwards the 
indicator (12) will be deemed.

• Move the steam control handle (3) up-

wards. When the cup is full turn the steam 
control handle (3) into OFF position. Re-
peat the operation until the water tank (4) 
is empty. The coffee machine is ready for 
use (see Pic. 4).

How to get good espresso

•  Use the coffee powder intended special-

ly for the espresso coffee machines.

•  Ram the coffee powder in the filter slight-

ly.

•  The strength and flavor of the coffee de-

pends upon sort and quality of the coffee 
beans, and also upon the grade of coffee 
powder grinding. If coffee is pouring out 
for too long this means the coffee powder 
is too fine or it is rammed too strongly.

Making espresso

• Insert the power cord plug into the wall 

outlet.

•  Detach the tank (4), fill it with cold water 

up to the MAX mark, and install the tank 
into its former position (see Pic. 1).

•  Insert the filter (8) into the holder (9).
•  Fill the filter (8) with the coffee powder.
• Install the holder (9) into the installation 

position (7) by rotating it to the right up to 
the stop (see Pic. 2). 

• Put the cup of the appropriate high on 

the tray (11).

• Switch the coffee machine on by press-

ing the button (14). The indicator (13) is 
lighted. The indicator (12) keeps blinking 
until the set temperature is reached, af-
terwards it will be deemed.

• The coffee machine is ready for prepar-

ing espresso.

• Turn the steamer supply control handle 

(3) upwards. After the cup has been filled 

turn the steamer supply control handle 
(3) into OFF position (see Pic. 4).

Attention!

-  Do not detach the filter holder (9) imme-

diately after preparing coffee as there is 
redundant water vapor pressure inside.

Making cappuccino

•  You can whip cream or milk to make cap-

puccino coffee, heat water to make some 
tea or warm up any other beverages by 
hot steam.

• Fill the tank (4) with water and install it 

into the proper position (see Pic. 1).

• Switch the coffee machine on by press-

ing the button (14), and wait until the in-
dicator (12) is deemed.

•  Put the appropriate can for collecting the 

water under the steam outlet nozzle (5). 

•  Turn on the steam supply by rotating the 

control handle (3) downwards to remove 
the condensate out of the steam pipe. 
After the condensate has been removed 
set the control handle (3) into OFF posi-
tion (see Pic. 5). 

• Fill the tank with cold milk (it is recom-

mended to use the milk containing 2% of 
fat) per one third.

• 

Put the steam nozzle (6) into the can 
filled with milk, turn the control handle 
(3) downwards, the steam supply is on. 
Several seconds are enough to make the 
thick foam. The steam nozzle (6) should 
not touch the bottom of the can. Other-
wise the steam release would be blocked 
(see Pic. 6).

Important: 

clean the steam pipe (5) imme-

diately after whipping the cream or milk:
put any can for collecting the water under 
the steam nozzle, switch on the steam sup-
ply for several seconds by the control (3) 
(see Pic. 3). 

Attention! 

Be aware of the hot steam go-

ing out to avoid skin burns.

1508.indd   5

1508.indd   5

15.05.2007   9:57:09

15.05.2007   9:57:09