Braun KMM 30 - Инструкция по эксплуатации - Страница 5

5

English

Our products are engineered to meet the highest 

standards of quality, functionality and design. We hope 

you thoroughly enjoy your new Braun coffee mill.

Caution

Read all instructions carefully before using this 

product.

• This appliance is for household use. It must be kept 

out of the reach of children!

• Before plugging into a socket, check whether your 

voltage corresponds with the voltage printed on the 

bottom of the appliance.

• Always unplug the appliance before cleaning, and 

before removing the coffee bean receptacle from 

the motor block.

• Braun electric appliances meet applicable safety 

standards. Repairs on electric appliances must only 

be done by authorized service personnel.

• Faulty, unqualified repair work may cause accidents 

or injury to the user.

• The cord of the appliance may only be replaced by 

an authorized Braun Service Centre as a special tool 

is required.

Description

1

On/off switch and timer/measurer

(the appliance is switched off at setting 

«timer off/0»)

2

Motor block

3

Grind fineness scale

4

Grind selector ring

5

Coffee bean receptacle

6

Lid for the coffee bean receptacle 

5

7

Fineness marker on the grind selector ring 

4

8

Lid for the coffee grounds receptacle 

9

9

Coffee grounds receptacle

j

Measuring spoon with cleaning spatula

Plugging in

Pull out only as much cord from the cord storage as you 

need to the socket (a).

Grinding coffee

Notice: To retain the full flavour of the coffee beans, 

the coffee bean receptacle should be always properly 

closed with the lid.

Only the immediately needed quantity of coffee should 

be ground at a time.

Setting the degree of fineness:

The grind fineness scale has two general sections: one 

for filter coffee («filter coffee») and one for espresso-

type coffee («espresso»).

Set the desired degree of coffee grounds fineness by 

turning the grind selector ring so that the fineness 

marker points to the desired dot on the grind fineness 

scale (b).

The grind selector ring 

4

 is screwed into the motor 

block and can be turned from one end of the grinding 

fineness spectrum to the other. If you turn the grind 

selector ring anti-clockwise, the grind will be coarser 

the higher the figures and the larger the dots on the 

grind fineness scale are.

Notice: When using a coffeemaker, the coffee grounds 

should not be too fine, as this could result in the 

coffeemaker overflowing, as water would not be able to 

flow as designed through the filter. For espresso-type 

coffee you should try starting with a medium setting in 

the «espresso» section of the grind fineness scale, and 

adjust so that two cups of espresso takes approxi-

mately 25 seconds to brew, once the coffee starts to 

drip out of the filter of your espressomaker.

Turning on the coffee mill:

The coffee mill is switched on by turning the switch 

clockwise. Turn the switch until you have reached the 

right setting for the desired quantity of coffee grounds 

(c). The marking numbers are shown on the timer scale 

around the timer switch.

By returning the on/off switch to position «timer off/0», 

you may stop or shorten the grinding process at any 

time.

Removing the coffee grounds

When grinding is completed, remove the lid from the 

coffee grounds receptable and take out the coffee 

grounds with the measuring spoon.

The coffee grounds receptacle can also be pulled off 

from the motor block horizontally (d). A measuring 

spoon full of coffee grounds is approximately 6.5 g, 

generally the quantity needed for 1 cup of brewed 

coffee or espresso.

Cleaning

Before cleaning, always first unplug the appliance. 

Do not immerse the motor block in water and do not 

hold it under running water. Wipe the motor block with 

a damp cloth only.

The coffee grounds outlet can be cleaned with the 

spatula on the reverse end of the measuring spoon (e). 

The coffee bean receptacle, the lid, the coffee grounds 

receptacle and the lid may be cleaned in the 

dishwasher.

Subject to change without notice.

This product conforms to the EMC-Requirements 

as laid down by the Council Directive 89/336/EEC 

and to the Low Voltage Regulation (73/23 EEC).