Кофемашина Siemens TK 56004 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
15
en
Settings and displays
Setting the water hardness
It is important that the water hardness be
set correctly, so that the appliance indicates
accurately when the descaling programme
should be run. The factory setting is a water
hardness of 4. You can check the water
hardness using the enclosed test strip or by
asking your local water supplier.
Degree Water hardness
German (°dH) French (°fH)
1
2
3
4
17
815
1623
2430
113
1427
2842
4354
● Determine the water hardness with the
enclosed test strip.
e.g. Hardness = 2
● Switch the appliance to “
eco
” mode.
● Hold down the steam button
h
for at
least 5 seconds. The number of service
buttons
4
,
5
,
eco
,
h
that light up
indicate the selected water hardness.
● Press the steam button
h
repeatedly
until the correct number of buttons is lit.
● Press button
eco
once. The selected
number of service buttons should light
up briefly; this indicates that the desired
water hardness setting has been saved
successfully.
If a water filter (special accessory) is used,
the water hardness should be set to 1.
Note:
If no button is pressed within 90
seconds, the appliance switches to stand
by mode without saving the new settings.
In this case, the previous water hardness
setting is retained.
The first time a filter is used or after
changing the filter, the appliance needs to
be cleaned.
● Fill the water tank up to the “0.5l” mark.
● Place a suitable container (approx. 0.5
litres) under the nozzle
9
.
● Turn the dial
8
to
g
/
h
.
● If no water comes out of nozzle
9
, turn
the dial back to ““
O
”..
● Fill the water tank and water pipes (see
section “Switching on the appliance”).
Setting the time for switchover to “eco”
mode
The appliance can be programmed so that
it automatically switches to “
eco
” mode
after a certain time (from 10 minutes to 4
hours).
● Switch the appliance to “
eco
” mode.
● Hold down the
5
button for at least 5
seconds.
If
4
lights up,
= switchover after 10 minutes
If
4
,
5
lights up,
= switchover after 30 minutes
If
4
,
5
,
eco
lights up,
= switchover after 2 hours
If
4
,
5
,
eco
,
h
lights up,
= switchover after 4 hours
● Press the
5
button to set the required
time.
● Press the
eco
button to save the setting.
Note:
The factory setting is 10 minutes.
Adjusting the grinding unit
Sliding switch
16
adjusts the degree of
grinding, from coarse to fine.
Warning
Adjust the grinding unit only while it is
running! Otherwise the appliance may be
damaged.
● Press the coffee dispensing button
4
.
● While the grinding unit is running, move
the sliding switch
16
to the desired
position: the smaller the dots, the finer the
grind.
i
The new setting will not become apparent
until the second or third cup is brewed.
Tip:
For dark roast coffee beans, choose a
coarser grind; for light roast beans, select a
finer grind.
