Condtrol Vector 30 - Инструкция по эксплуатации - Страница 2

MESSAGE CODES

While operation, the following codes/symbols may appear on the display:

Message 

code 

Problem 

Solution

203

Battery is too low.

Replace the batteries.

402

Calculation error.

Make measurement again.

301

Temperature is too 

high.

Cool down the device to 

operating temperature range.

302

Temperature is too 

low.

Warm up the device to 

operating temperature range.

101

Reflected signal is too 

weak.

Choose the surface with 

stronger reflectance. Use the 

reflecting plate.

102

Reflected signal is too 

strong.

Choose the surface with weaker 

reflectance. Use the reflecting 

plate.

201

Ambient light is too 

strong.

Make measurements in less 

illuminated zone.

401

Hardware error.

Switch on/off the device 

several times. If the symbol 

still appears, then the device 

may be defective. Contact the 

store where the device was 

purchased, or an authorized 

service center.

CARE AND MAINTENANCE
Attention! The instrument is a precise device and requires careful 

handling. The following recommendations will extend the life of the 

device:

- Do not point the device at the sun.

- Protect the device from bumps, falls, and excessive vibration; do not let 

liquids, construction dust and foreign objects get inside the device.

- Do not expose the device to extreme temperatures.

- If liquids get inside the device first remove the batteries, then contact 

the service center.

- Do not store or use the device under high humidity conditions for a long 

time.

- Clean the device with soft wet cloth.

- Keep device optics clean and protect it from mechanical damage.

-  Сarry  out  control  measurements  occasionally,  especially  if  the  device  is 

subject to excessive mechanical or other impact, before and after taking 

important measurements.

Failure to observe the following rules may lead to leakage of electrolyte 

from the batteries and damage of the device: 

- Remove the batteries from the device if it is not used for a long time.

- Do not use batteries of different types, with different charge level.

- Do not leave discharged batteries in the device.

UTILIZATION

Expired tools, accessories and package should be passed for waste recycle. 

Please send the device to the following address for proper recycle:

CONDTROL GmbH 

Wasserburger Strasse 9 

84427 Sankt Wolfgang 

Germany 

Do not throw the device in municipal waste!

According  to  European  directive  2002/96/ЕC  expired  measuring  tools 

and their components must be collected separately and submitted to 

environmentally friendly recycle of wastes.

WARRANTY

All CONDTROL GmbH devices go through post-production control and are 

governed by the following warranty terms. The buyer’s right to claim about 

defects and general provisions of the current legislation do not expire.

1) CONDTROL GmbH agrees to eliminate all defects in the device, discovered 

during the warranty period, that represent the defect in material or 

workmanship in full volume and at its own expense.

2) The warranty period is 24 months and starts from the date of purchase by 

the end customer (see the original supporting document).

3)  The  warranty  doesn’t  cover  defects  resulting  from  wear  and  tear  or 

improper use, malfunction of the device caused by failure to observe the 

instructions of this user manual, untimely maintenance and service and 

insufficient care, the use of non-original accessories and spare parts. 

Modifications in design of the device relieve the seller from responsibility for 

warranty works. The warranty does not cover cosmetic damage, that doesn’t 

hinder normal operation of the device.

4)  CONDTROL  GmbH  reserves  the  right  to  decide  on  replacement  or  repair 

of the device. 

5) Other claims not mentioned above, are not covered by the warranty. 

6) After holding warranty works by CONDTROL GmbH warranty period is not 

renewed or extended.

7) CONDTROL GmbH is not liable for loss of profit or inconvenience associated 

with a defect of the device, the rental cost of alternative equipment for the 

period of repair. 

This warranty applies to German law except provision of the United Nations 

Convention on contracts for the international sale of goods (CISG).

In warranty case please return the device to retail seller or send it with defect 

description to the following address:

CONDTROL GmbH 

Wasserburger Strasse 9 

84427 Sankt Wolfgang 

Germany