Liebherr KX 1021 Comfort - Инструкция по эксплуатации - Страница 3

Dimensions [mm]

Switching the appliance on and off

You are recommended to clean the appliance before swit-

ching it on for the first time (see "

Cleaning").

•  Turn  the  temperature  control   

1

  clockwise  from  "0"  to 

"1". The appliance is now switched on.

Setting the temperature

Turn  the  temperature  control   

1

  to  set  the  desired  tem-

perature.
Setting "1" = lowest cooling setting, 

                      highest temperature

Setting "7" = highest cooling setting, 

                      lowest temperature
Remember that the temperature depends on the ambient 

temperature (location of appliance), the number of times the 

door is opened and how much frozen food is stored. The 

setting should be adjusted accordingly if necessary.

Interior light

Bulb data: 15 W (never use a bulb rated at more than 15 W).  

The  voltage  should  agree  with  the  details  on  the  type 

plate.

Socket: E 14.
Replacing the bulb:

Pull out the mains plug or remove/unscrew the fuse.

Reach behind the cover, unscrew the bulb and replace.

Connecting to the mains

Power supply (a.c.) and voltage at the operating point must 

comply with the details on the type plate which is located on the 

left-hand inside wall, next to the top freezer drawer. The socket 

must be fused with a 10 A fuse or higher. The socket should be 

easily accessible and not directly behind the appliance.

• Do not connect the appliance to the supply with other 

equipment using a distribution outlet - risk of overheating.

• 

Connect the appliance through a properly earthed plug 

   and socket. 

Setting up

• The floor on which the appliance stands should be horizon-

tal and level. To compensate for any unevenness, adjust the 

height of the feet with the open-ended wrench supplied. The 

appliance can be placed with its back flush to the wall. 

• Always position the appliance directly up against the wall.

• The ventilation grilles should not be obstructed.

• Condensation may form on the outside of the refrigerator/

freezer during periods of high humidity. 

   Constant ventilation of the installation site is recommend.

• Do not place heat-emitting appliances, e.g. microwave oven, 

toaster, etc., on top of the freezer. 

• Keep burning candles, lamps and other items with naked 

flames away from the appliance so that they do not set the 

appliance on fire.

• Standard EN 378 specifies that the room in which you install 

your appliance must have a volume of 1 m

3

 per 8 g of R 

600a refrigerant used in the appliance, so as to avoid the 

formation of inflammable gas/air mixtures in the room where 

the appliance is located in the event of a leak in the refrigerant 

circuit. The quantity of refrigerant used in your appliance is 

indicated on the type plate on the inside of the appliance.

• Fire hazard due to dampness!

   If live parts or the mains lead become damp this may cause  

short circuits.

- The appliance is designed for use in enclosed areas. Do not 

operate the appliance outdoors or in areas where it is ex-

posed to splash water or damp conditions.

• CAUTION! Risk of injury and danger of damage as a result of 

incorrect transport!

- Transport the appliance in a packed condition.

- Transport the appliance upright.

- Do not transport the appliance without assistance.

•

 The appliance may be moved only when it is empty.

      h         a         g         e         e'         d         c         c'     

    630     554     610     624      653    1129     562      591

Saving energy

-  Always ensure good ventilation. Do not cover ventilation

  openings or grille.

-  Do not place appliance in areas of direct sunlight or next to a

  stove, heater or similar object.

-  The energy consumption depends on the installation condi-

tions, e.g. the ambient temperature.

-  Keep the time the appliance is open to a minimum.

-  The lower the temperature setting, the higher the power

  consumption.

-  Store food logically.

-  Ensure that all food is well packed and covered for storage.

  This will prevent frost from forming.

-  Remove food as needed in order that it does not warm too

  much.

-  First cool warm food to room temperature before storing it.

-  Defrost frozen food in the refrigerator.

-  If there is a thick layer of frost in the appliance: defrost the 

appliance.

Accumulated dust increases the energy 

consumption:

-  Once a year, dust the refrigerating unit 

together with the metal grille of the heat

  exchanger at the back of the appliance.