Газонокосилки Husqvarna LC 353VB 9672392-01 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
English
– 77
MAINTENANCE
General
•
Let your Husqvarna dealer regularly check the machine
and make essential adjustments and repairs.
•
Always use genuine accessories.
Maintenance schedule
In the maintenance schedule you can see which parts of your
machine that require maintenance, and with which intervals it
should take place. The intervals are calculated based on daily
use of the machine, and may differ depending on the rate of
usage.
*See instructions in the section "Machine’s safety
equipment".
General inspection
•
Check that nuts and screws are tight.
LC353VB
Make sure the cable clip is properly secured to the bracket. If
the cable clip feels loose or have fallen of, mount the clip back
into place.
External cleaning
•
Brush leaves, grass and the like off of the lawn mower.
•
Do not use a high pressure washer to clean the machine.
•
Never flush water directly on the engine.
•
Clean the air intake on the starter. Check the starter and
starter cord.
•
When cleaning under the cutting deck, turn the machine
with the spark plug upwards. Empty the fuel tank.
Cleaning of the gear housing.
•
Remove the service hatch.
•
Brush leaves and grass off of gear housing. If necessary
clean the gear housing with water. For
LC348Ve
and
LC353VE
make sure the battery is disengaged.
Oil level
The lawn mower should stand on flat ground when you check
the oil level. Check the oil level with the dipstick on the oil filler
cap.
•
Remove the oil cap and wipe the dipstick clean.
•
Put the dipstick back in. The oil filler cap must be
completely screwed down to give a correct picture of the
oil level.
•
If the oil level is low, fill using engine oil up to the upper
level on the dipstick.
Oil change
•
Empty the fuel tank.
•
Unscrew the oil filler cap.
•
Place a suitable vessel to collect the oil in.
•
Drain the oil by tipping the engine so that the oil runs out
through the filler pipe. Ask where you can dispose of
surplus engine oil at your local petrol station.
•
Fill with new engine oil of a good quality. See instructions
in the section "Technical data".
Cutting equipment
•
Damaged blades should be replaced when hitting
obstacles that result in a breakdown.
•
Replacement or sharpening of the blades must be carried
out by an authorised service workshop.
!
WARNING! The user must only carry out the
maintenance and service work described in
this Operator's Manual. More extensive work
must be carried out by an authorized service
workshop.
Prevent unintentional starting by removing
the ignition cable from the spark plug.
The life span of the machine can be reduced
and the risk of accidents can increase if
machine maintenance is not carried out
correctly and if service and/or repairs are
not carried out professionally. If you need
further information please contact your
nearest service workshop.
Daily
maintenance
Weekly
maintenance 50 hours
At least once
a year
General
inspection
Spark plug
Replacing and
adjusting the V-
belt
Replacing and
adjusting the
V-belt
Oil level
Muffler*
Air filter
Air filter
External
cleaning
Vibration
damping
system*
Fuel system
Fuel system
Cutting
equipment
Oil change
Oil change
Cutting cover
and protective
cover*
Engine brake
handle*
!
WARNING! Always wear heavy-duty gloves
when servicing and maintaining the cutting
equipment. The cutters are very sharp and
cuts can occur very easily.
