Газонокосилки GreenWorks G24LM33K2 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
4.5
OPERATION TIPS
•
Do not try to override the operation of the start button or
switch box handle.
•
Do not tilt the machine when you start it.
•
Do not put hands or feet near or below the turning parts.
•
Keep the discharge chute clean.
•
Do not cut wet grass.
•
Higher blade height is necessary for new or thick grass.
•
Clean the bottom of the mower deck after each use.
Remove grass clippings, leaves, dirt, and other debris.
5
MAINTENANCE
WARNING
Remove the safety key and battery pack from the machine
before maintenance.
WARNING
Keep the motor and battery pack free from grass, leaves or
too much grease.
CAUTION
Use only approved replacement parts.
CAUTION
Do not let brake fluids, gasoline, petroleum-based materials
touch the plastic parts. Chemicals can cause damage to the
plastic, and make the plastic unserviceable.
CAUTION
Do not use strong solvents or detergents on the plastic
housing or components.
NOTE
Recommended tightening torque (blade): 33-37 Nm.
5.1
GENERAL MAINTENANCE
•
Before each use, examine the machine for damaged,
missing, or loose parts such as screws, nuts, bolts and
caps.
•
Tighten correctly all the fasteners and caps.
•
Clean the machine with a dry cloth. Do not use water.
5.2
REPLACE THE BLADE
Figure 9.
WARNING
Use only approved replacement blades.
WARNING
Wear heavy gloves or wind cloth around the blade when
you touch the blade.
1. Stop the machine.
2. Make sure that the blade fully stops.
3. Remove the safety key and battery pack.
4. Turn the machine to its side.
5. Use a piece of wood to prevent the movement of the
blade.
6. Remove the mounting nut and spacer with a wrench or
socket.
7. Remove the blade.
8. Install the new blade. Make sure that the raised points
engage the hole(s) in the blade.
9. Put in the mounting nut and spacer and tighten them.
5.3
STORE THE MACHINE
•
Clean the machine before storage.
•
Make sure that the motor is not hot when you store the
machine.
•
Make sure that the machine does not have loose or
damaged parts. If it is necessary, do these steps/
instructions:
•
Replace the damaged parts.
•
Tighten the bolts.
•
Speak to a person of an approved service center.
•
Store the machine in a dry area.
•
Make sure that children cannot come near the machine.
6
TROUBLESHOOTING
Problem
Possible cause
Solution
The handle is not
in position.
The bolts are not
engaged correctly.
Adjust the height
of the handle and
make sure that the
knobs and bolts
are aligned cor-
rectly.
The machine does
not start.
The battery ca-
pacity is low.
Charge the battery
pack.
The handle switch
is defective.
Replace the handle
switch.
The battery key is
not put in.
Put in the battery
key.
The machine cuts
grass unevenly.
The lawn is rough. Examine the mow-
ing area.
The blade height is
not set correctly.
Move the wheels
to a higher posi-
tion.
7
English
EN
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
