Einhell GE-CM 33 Li 3413140 - Инструкция по эксплуатации - Страница 25

GB

- 25 -

Always mow along inclines (not up and down). 

You can prevent the lawn mower from slipping 

down by holding a position at an angle upwards.

Select the cutting height according to the length 

of the grass. Make several passes so that no 

more than 4cm of grass are cut at one time.

Switch o

ff

  the motor before doing any checks on 

the blade. Keep in mind that the blade continues 

to rotate for a few seconds after the motor has 

been switched o

ff

 . Never attempt to manually 

stop the blade. Regularly check to see if the 

blade is securely attached, is in good condition 

and is sharp. If the contrary is the case, sharpen 

the blade or replace it. In the event that the blade 

strikes an object, immediately switch o

ff

  the lawn 

mower and wait for the blade to come to a com-

plete stop. Then inspect the condition of the blade 

and the blade mount. Replace any parts that are 

damaged.

As soon as grass clippings start to trail the lawn 

mower, it is time to empty the grass basket. Im-

portant! Before taking o

ff

  the grass basket, switch 

o

ff

  the motor and wait until the blade has come to 

a stop.

To take o

ff

  the grass basket, use one hand to lift 

up the chute 

fl

 ap and the other to grab onto the 

basket handle. Remove the basket. For safety 

reasons, the chute 

fl

 ap automatically falls down 

after removing the grass basket and closes o

ff

  the 

rear chute opening. If any grass remains in the 

opening, it will be easier to restart the engine if 

you pull the mower back approximately 1m.

Do not use your hands or feet to remove clippings 

in or on the mower housing, but instead use suita-

ble tools such as a brush or a hand broom.

In order to ensure that the majority of grass clip-

pings are picked up, the inside of the grass bas-

ket must be cleaned after each use.

Reattach the grass basket only when the motor is 

switched o

ff

  and the blade has stopped.

Lift up the chute 

fl

 ap with one hand and, holding 

the grass basket by its handle with the other 

hand, hang in the basket from the top.

7.  Cleaning, maintenance and 

ordering of spare parts

Danger!

 Pull the safety plug before carrying out any 

cleaning work (Fig. 13).

7.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 Do not clean the lawn mower with running 

water, particularly with high-pressure water.

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could 

attack the plastic parts of the equipment. En-

sure that no water can seep into the device. 

7.2 Carbon brushes

In case of excessive sparking, have the carbon  

brushes checked only by a quali

fi

 ed electrician.

Danger!

 The carbon brushes should not be rep 

laced by anyone but a quali

fi

 ed electrician.

7.3 Maintenance

• 

 Worn out or damaged blades, blade mounts, 

and bolts should be replaced as a set by an 

authorized professional in order to keep the 

equipment in balance.

• 

 Ensure that all mounting components (i.e. 

screws, bolts, nuts etc.) are always tightened 

so that the equipment can be safely operated 

at all times.

• 

 Frequently check the grass catch assembly 

for signs of wear.

• 

 Replace excessively worn or damaged parts 

immediately.

• 

 In order to ensure that you enjoy the equip-

ment for many years to come, all screwed 

parts, as well as the wheels and axles, should 

be cleaned and lubricated.

• 

 Keeping your lawn mower in good condition 

not only ensures a long lifespan and high per-

formance, but also enables the equipment to 

thoroughly cut your grass with minimal effort. 

• 

 The blade is subjected to more wear and 

tear than any other component. Therefore, 

routinely check the condition of the blade 

Anl_GE_CM_33_Li_Kit_Solo_SPK7.indb   25

Anl_GE_CM_33_Li_Kit_Solo_SPK7.indb   25

10.10.2016   16:14:29

10.10.2016   16:14:29