Einhell GE-CM 33 Li 3413140 - Инструкция по эксплуатации - Страница 23

GB

- 23 -

• 

 Switch the appliance off when it is not in use.

• 

 Wear protective gloves.

5.  Before starting the equipment

The lawn mower is delivered partly assembled. 

The push bar and the grass basket must be as-

sembled before using the lawn mower. Follow the 

instructions step by step and refer to the pictures 

when assembling.

Mounting the push bar (Fig. 3 to 5)

Start by fastening the lower push bars for the left-

hand side (Fig. 3/Item 10) and the right-hand side 

(Fig. 3/Item 11) to the mower housing using the 

fastening screws (Fig. 3/Item 12). The upper push 

bar then has to be slid onto the lower push bars 

and fastened with screws (Fig. 4/Item 13). There 

are 2 di

ff

 erent holes on each of the lower push 

bars for this, to enable the height of the push bar 

to be adjusted to the height of the user. Then fas-

ten the power cable to the push bar with the cable 

clips (Fig. 5/Item 14).

Mounting the catch basket (see Fig. 6)

Before you 

fi

 t the catch basket you must ensure 

that the motor is switched o

ff

  and the blade is not 

rotating. Lift the ejector 

fl

 ap (Fig. 6/Item 6) with 

one hand. With the other hand, hold the catch 

basket by the handle and hook it in from above 

(Fig. 6).

Filling level indicator of the grass collector

The grass box is equipped with a 

fi

 lling level in-

dicator (Fig. 1/Item 15). which is opened by the 

air

fl

 ow that the lawn mower generates during ope-

ration. If the 

fl

 ap closes during mowing, the grass 

collecting device is full and must be emptied. To 

ensure the proper functioning of the 

fi

 lling level 

indicator, the holes under the 

fl

 ap must always be 

kept clean and passable.

Adjusting the cutting height

Caution!

Adjust the cutting height only when the machine 

has been switched o

ff

  and the safety plug has 

been pulled out.

Before you begin to mow, check to ensure that the 

blade is not blunt and that none of the fasteners 

are damaged. To prevent any imbalance, replace 

blunt and/or damaged blades. To carry out this 

check, 

fi

 rst switch o

ff

  the motor and pull out the 

safety plug.

The cutting height is adjusted as follows (see Fig. 

7):

1.  Push the lever (5) downwards.

2.  Set the lever (5) to the desired cutting height.

3.  Release the lever (5) and check that it is se-

curely seated in the lock.

Reading o

ff

  the cutting height

The cutting height can be set between 25-65 mm 

in 5 intervals, and can be read o

ff

  on the scale.

Charging the battery (Fig. 8)

1.  Take the battery pack out of the equipment. 

Do this by pressing the side pushlock buttons.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(9) into the socket outlet. The green LED will 

then begin to 

fl

 ash.

3.  Insert the battery pack (8) into the battery 

charger (9).

4.  In the section entitled „Charger indicator“ you 

will 

fi

 nd a table with an explanation of the LED 

indicator on the charger.

The battery pack can become a little warm during 

the charging. This is normal.

If the battery pack fails to charge, check:

• 

 whether there is voltage at the socket outlet

• 

 whether there is good contact at the charging 

contacts

If the battery pack still fails to charge, send

• 

 the charging unit

• 

 and the battery pack

to our customer service center.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly. 

You must recharge the battery pack when you 

notice that the performance of the device drops. 

Never allow the battery pack to become fully di-

scharged. This will cause it to develop a defect.

Installing the battery (Fig. 9-10)

Open the battery cover. This is done by pulling 

the snap fastener (Item A) as shown in Fig. 9 and 

swinging up the cover. Then insert the two batte-

ries in the mounts as shown in Fig. 10.

Anl_GE_CM_33_Li_Kit_Solo_SPK7.indb   23

Anl_GE_CM_33_Li_Kit_Solo_SPK7.indb   23

10.10.2016   16:14:29

10.10.2016   16:14:29