Фритюрницы Kenwood DF560 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
know your Kenwood deep fryer
safety
●
Read all instructions.
●
Never plug in the fryer before filling the bowl with oil.
●
Keep children away during use and after - fat stays hot
for a long time.
●
Never let the cord touch hot surfaces or hang down
over the worktop edge - a child could grab it and pull
the fryer down. Place excess cord in cord storage area
at the back of the fryer.
●
Never touch the bowl, pour away oil or move your fryer
while the oil’s hot.
●
Never touch hot surfaces especially the lid and metal
trim.
●
Never put the electronic control in water. Remove it
before washing the rest of your fryer.
●
After cleaning, ensure the bowl and its electric pins are
dry before use.
●
Never leave your fryer on unattended.
●
This fryer is not intended for use by young children or
infirm persons without supervision.
●
Young children should be supervised to ensure that
they do not play with this appliance.
●
Take care when removing the electronic control - the
temperature probes may be hot.
●
Do not use if there is any damage to the fryer, cord or
plug. Get it checked or repaired: see ‘service’.
●
Only use the electronic control supplied with the DF560
model.
●
Watch out for steam during cooking and when you
open the lid.
●
Never put your fryer near or on cooker hot plates.
●
This fryer is for domestic use only.
●
Always unplug the fryer after use.
before plugging in
●
Make sure your electricity supply is the same as the
one shown on the underside of the electronic control.
●
This machine complies with European Economic
Community Directive 89/336/EEC.
before using for the first time
1 Remove all packaging.
2 Dismantle: see ‘to dismantle, assemble and use your
fryer’.
3 Wash the parts: see ‘cleaning’.
know your Kenwood fryer
removable lid with permanent mesh filter
viewing window
lid seal
condensation trap
rise and fall control
pouring lips
removable bowl
lid release
carrying handles
electronic temperature control unit
on/off button
temperature buttons - 150, 170, 190°C
oil change light
timer
temperature probes
cord storage
to dismantle, assemble and use
your fryer
to dismantle
1 Push the lid release
down to open the lid. Then lift
the lid off.
2 Lift up the handle and remove the basket.
3 Pull out the electronic control unit and then remove the
bowl.
●
Before removing the electronic control unit
check that the cord is released from the cord
storage area at the back of the fryer
.
to assemble and use
1 Insert the bowl – ‘MAX’ and ‘MIN’ marks to the back of
the fryer.
2 Then insert the electronic control unit
– cord to the
back of the fryer
+
.
3 Pour in the oil. The level must be between the ‘MAX’
and ‘MIN’ marks
.
4 Insert the basket and close the lid. Then lower the
handle by sliding back the rise & fall control
.
5 Plug in and switch on
. Press the button for the
required temperature
and the light will come on.
Note: When the oil reaches the right
temperature for frying a single beep will
sound and the light will flash slowly.
2
