Valera Hospitality Silent Jet Protect 1200 - Инструкция по эксплуатации - Страница 3

INSTALLATION INSTRUCTIONS 

Wall holder model 044.01 - 044.02 - 
044.03 - 044.04 - 044.05 - 044.06 

Model 044.01 (Fig. 1) 

Basic model with ON-OFF switch. 

Model 044.02 (Fig. 2) 

Model with 16 A European standard socket and ON-OFF switch.  

Model 044.03 (Fig. 3) 

Model with 10 mA (*) differential switch, 16 A European standard 
socket and ON-OFF switch. 

Model 044.04 (Fig. 4) 

Model with 10 mA (*) differential switch and ON-OFF switch. 

Model 044.05 (Fig. 5) 

Model with universal shaver socket (**) and ON-OFF switch.  

Model 044.06 (Fig. 6) 

Model with 10 mA (*) differential switch, universal shaver socket 
(**) and ON-OFF switch.  

(*) The appliance is equipped with a 10 mA differential switch. 
 
(**) A safety transformer isolates the shaver socket from the 
mains electricity and a protective device prohibits the use of 
appliances with a power greater than 20 VA.  
 

Installation of wall holder 

This work should only be carried out by a suitably qualified electrical 
engineer, in order to comply with the existing national safety regulations. 
When the spiral cord is extended to its maximum length, the hairdryer 
shall not be reached by a person using the bath or the shower. 
There are two possible methods of installation: 

A = for fixed connection lead 
B = for mobile connection lead 

Attention: before installing the hairdryer 
always switch off the general switch  
of your mains electricity. 

Method A (for fixed connection lead) for 
wall holder model  044.01 - 044.04 
044.05 - 044.06 

The connection wiring from the mains for wall holder models  
044.01 - 044.04 - 044.05 - 044.06 must be type 2x1,5 mm

2

. 

1. Separate the cover (1) of the wall holder from the back plate by 

loosening the screw (14). 

2. Remove the knockout (2) provided in the back plate of the wall 

holder. 

3. Feed the mains supply cable (3) coming out of the wall into the 

hole in the back plate left after removing the knockout (2). 

4. Secure the back plate of the wall holder to the wall using the plugs 

and screws provided. 

5. Remove the terminal connector (4), connect the mains supply 

cable (3) to the terminal connector (4), as shown in the picture, and 
then secure again the terminal connector (4). 

6. Model 044.01 - 044.04 - 044.05 - 044.06 are double insulated 

and no ear th connection is provided. 

7. Fit the front cover of the wall holder, taking care to locate the cable 

sleeve (6) properly. Secure the front cover with the screw (14). 

8. Switch on the general switch of your mains electricity. The 

hairdryer is ready for use. 

Method B: (for mobile connection lead) 
only for wall holder model 044.01 - 044.04 
044.05 - 044.06 

The connection wiring from the mains for wall holder models 044.01 
044.04 - 044.05 - 044.06 must be type H05VV-F 2x1,5 mm

2

. 

1. Separate the cover (1) of the wall holder from the back plate by 

loosening the screw (14). 

2. Remove the knockout (8) provided in the base of the back plate 

of the wall holder for feeding the cable sleeve (11). 

3. Secure the back plate of the wall holder to the wall using the plugs 

and screws provided. 

4. Strip the power supply connection cable (13), inser t the cable 

bushing (11), remove the terminal (9), connect the cable (13) to 
the terminal (9) and reposition the terminal (9). Position the 
stripped par t of the cable carefully, as indicated in the picture. 
Secure the cable bushing (10) using the corresponding screws. 
Caution: this appliance has double insulation and is not fitted with 
an ear thing system. 

5. Locate the cable sleeves (6) and (11) in the slot provided in the 

base of the back plate. 

6. Fit the front cover of the wall holder, taking care to locate the cable 

sleeves (6) and (11) properly. 

7. Secure the front cover with the screw (14). 
8. Switch on the general switch of your mains electricity. The 

hairdryer is ready for use. 

Method C (with mobile connection) for 
models 044.02 - 044.03 

See Method B: only variant: 
- The power cable for mounts 044.02 - 044.03 must be type 

H05VV-F 3G x 2.5 mm

2

 and must be connected to the tripolar 

terminal (7) 

OPERATING INSTRUCTIONS 

Switching 

Wall mount switch 

(Fig. 7, 1)

appliance placed in the mount = off 
appliance out of the mount = on 
 

Differential switch 
(Mod. 044.03, 044.04, 044.06 only) 

The differential switch (Fig. 9 and 10), in the event of a fault in the 
electrical circuit to which it is connected, is triggered and cuts off the 
power supply to the mount and the hair dryer. (Fig. 9) 

• Allow your appliance to cool before storing away and do not wrap the 

supply cord around the hairdryer in storage. 

• The A-weighted sound pressure level of the hairdryers for commercial use 

is below 70 dB(A). 

7

00060812 int_dic2020_Layout 1  07/01/2021  10:19  Pagina 7