Skil 1558 - Инструкция по эксплуатации - Страница 6

6

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained 

users.

e) 

Maintain power tools. Check for misalignment or 

binding of moving parts, breakage of parts and any 

other condition that may affect the power tool's 

operation. If damaged, have the power tool repaired 

before use.

 Many accidents are caused by poorly 

maintained power tools.

f) 

Keep cutting tools sharp and clean.

 Properly 

maintained cutting tools with sharp cutting edges are 

less likely to bind and are easier to control.

g) 

Use the power tool, accessories and tool bits etc., 

in accordance with these instructions, taking into 

account the working conditions and the work to 

be performed.

 Use of the power tool for operations 

different from those intended could result in a hazardous 

situation.

5)  SERVICE

a) 

Have your power tool serviced by a qualified repair 

person using only identical replacement parts.

This will ensure that the safety of the power tool is 

maintained.

SAFETY INSTRUCTIONS FOR PLANERS

GENERAL

• 

This tool should not be used by people under the age 

of 16 years

• 

The noise level when working can exceed 85 dB(A); 

wear ear protection

④

• 

Dust from material such as paint containing lead, some 

wood species, minerals and metal may be harmful 

(contact with or inhalation of the dust may cause allergic 

reactions and/or respiratory diseases to the operator or 

bystanders); 

wear a dust mask 

⑤

 and work with a 

dust extraction device when connectable

• 

Certain kinds of dust are classified as carcinogenic 

(such as oak and beech dust) especially in conjunction 

with additives for wood conditioning; 

wear a dust mask 

⑤

 and work with a dust extraction device when 

connectable

• 

Follow the dust-related national requirements for the 

materials you want to work with

• 

SKIL can assure flawless functioning of the tool only 

when original accessories are used

• 

Never use the tool when cord is damaged; have it 

replaced by a qualified person

•  Always disconnect plug from power source before 

making any adjustment or changing any accessory

BEFORE USE

• 

Always check that the supply voltage is the same as 

the voltage indicated on the nameplate of the tool (tools 

with a rating of 230V or 240V can also be connected to 

a 220V supply)

• 

Avoid damage that can be caused by screws, nails and 

other elements in your workpiece; remove them before 

you start working

• 

Before using the tool check that the knives do not brush 

anywhere

• 

Use completely unrolled and safe extension cords with a 

capacity of 16 Amps (U.K. 13 Amps)

• 

Use clamps or another practical way to secure and 

support the workpiece to a stable platform

 (holding 

the work by your hand or against the body leaves it 

unstable and may lead to loss of control)

DURING USE

•  Hold power tool by insulated gripping surfaces, 

because the cutter may contact its own cord

(cutting a "live" wire may make exposed metal parts of 

the power tool "live"and shock the operator)

• 

Always keep the cord away from moving parts of the 

tool; direct the cord to the rear, away from the tool

• 

Keep your fingers away from the rotating knives

• 

In case of electrical or mechanical malfunction, 

immediately switch off the tool and disconnect the plug

• 

If the cord is damaged or cut through while working, do 

not touch the cord, but immediately disconnect the plug

• 

If any chip should get jammed in the chip outlet, you 

should switch off the motor, ensure that all moving parts 

have come to a complete standstill, disconnect the plug, 

and remove the jammed chip

AFTER USE

•  Wait for the cutter block to stop before setting the 

tool down

 (an exposed knife may engage the surface 

leading to possible loss of control and serious injury)

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• 

Do not connect the blue (= neutral) or brown (= live) wire 

in the cord of this tool to the earth terminal of the plug

• 

If for any reason the old plug is cut off the cord of 

this tool, it must be disposed of safely and not left 

unattended

USE

• 

Changing/reversing knives 

⑥

This planer is equipped with non-grindable knives with 

cutting edges on both sides; so if one side has become 

blunt, the other side can be used

!

switch off the tool and disconnect the plug

-

take wrench from storage A

-

turn tool upside down

-

loosen 3 bolts B with wrench (do not remove bolts)

-

push knife out of cutter block with piece of wood

-

put knife back in cutter block in reversed position, or 

use new knife

!

groove in knife should match ledge in cutter 

block

!

both knife ends should protrude equally

-

firmly tighten 3 bolts B with wrench

!

change/reverse knives in time; only use sharp 

knives

!

always change/reverse both knives at the same 

time

!

do not attempt to adjust the knives with 

cutter block screws C, which are pre-set at 

manufacturing

• 

Adjusting planing depth 

⑦

-

turn knob D in "+"/"-" direction for increasing/

decreasing planing depth

-

use indicator E as reference

-

always select a shallow planing depth and repeat the 

planing and adjusting process until the required depth 

is reached

• 

Chip outlet 

⑧

-

connect vacuum cleaner with adapter F to chip outlet 

G as illustrated

!

do not attempt to remove any obstructions from 

the chip outlet while knives are rotating