Makita DKP180Z - Инструкция по эксплуатации - Страница 10

10

Draw a cutting line on the workpiece. Insert the edge 
fence into the hole in the front of the tool. Align the blade 
edge with the cutting line. 

(Fig. 19)

Adjust the edge fence until it comes in contact with the 
side of the workpiece, then secure it by tightening the 
screw. 

(Fig. 20)

When planing, move the tool with the edge fence flush 
with the side of the workpiece. Otherwise uneven planing 
may result.
Maximum shiplapping (rabbeting) depth is 9 mm. 

(Fig. 21)

You may wish to add to the length of the fence by 
attaching an extra piece of wood. Convenient holes are 
provided in the fence for this purpose, and also for 
attaching an extension guide (optional accessory).

Chamfering (Fig. 22 & 23)

To make a chamfering cut as shown in the figure, align the 
“V” groove in the front base with the edge of the 
workpiece and plane it.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the 

battery cartridge is removed before attempting to 
perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the 

like. Discoloration, deformation or cracks may result.

Sharpening the planer blades

For conventional blades only (Fig. 24)

Always keep your blades sharp for the best performance 
possible. Use the sharpening holder (optional accessory) 
to remove nicks and produce a fine edge. 

(Fig. 25)

First, loosen the two wing nuts on the holder and insert 
the blades (A) and (B), so that they contact the sides (C) 
and (D). Then tighten the wing nuts. 

(Fig. 26)

Immerse the dressing stone in water for 2 or 3 minutes 
before sharpening. Hold the holder so that the both blades 
contact the dressing stone for simultaneous sharpening at 
the same angle.

Replacing carbon brushes (Fig. 27)

Remove and check the carbon brushes regularly. Replace 
when they wear down to the limit mark. Keep the carbon 
brushes clean and free to slip in the holders. Both carbon 
brushes should be replaced at the same time. Use only 
identical carbon brushes. 

(Fig. 28 & 29)

Use a screwdriver to remove the chip cover or nozzle. 

(Fig. 30)

Use a screwdriver to remove the brush holder caps. Take 
out the worn carbon brushes, insert the new ones and 
secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs, 
any other maintenance or adjustment should be 
performed by Makita Authorized Service Centers, always 
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended 

for use with your Makita tool specified in this manual. 

The use of any other accessories or attachments might 
present a risk of injury to persons. Only use accessory 
or attachment for its stated purpose.

If you need any assistance for more details regarding 
these accessories, ask your local Makita Service Center.
• High-speed steel Planer blade
• Tungsten-carbide Planer blade (For longer blade life)
• Mini planer blade
• Sharpening holder assembly
• Blade gauge
• Set plate set
• Edge fence (Guide rule)
• Extension guide set
• Dressing stone
• Nozzle
• Dust bag assembly
• Elbow
• Socket wrench
• Plastic carrying case
• Various type of Makita genuine batteries and chargers

NOTE:

• Some items in the list may be included in the tool 

package as standard accessories. They may differ 
from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according 
to EN60745:

Model DKP140

Sound pressure level (L

pA

): 80 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Model DKP180

Sound pressure level (L

pA

): 84 dB (A)

Sound power level (L

WA

): 95 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined 
according to EN60745:

Model DKP140

Work mode: planing softwood
Vibration emission (a

h

): 3.5 m/s

2

Uncertainty (K): 1.5 m/s

2

Model DKP180

Work mode: planing softwood
Vibration emission (a

h

): 4.5 m/s

2

Uncertainty (K): 1.5 m/s

2

ENG901-1

• The declared vibration emission value has been 

measured in accordance with the standard test method 
and may be used for comparing one tool with another.

• The declared vibration emission value may also be 

used in a preliminary assessment of exposure.

 WARNING:

• The vibration emission during actual use of the power 

tool can differ from the declared emission value 
depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the 

operator that are based on an estimation of exposure in 
the actual conditions of use (taking account of all parts