Ryobi MAX POWER RY36CSX35A-0 5133004595 - Инструкция по эксплуатации - Страница 7

5

English |

EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR

with a shield depicting a chainsaw to show compliance 

with EN 381-3. (Occasional users may use steel toe-

cap safety boots with protective gaiters which conform 

to EN 381-9 if the ground is even and there is little risk 

of tripping or catching on undergrowth)

Chainsaw jackets for upper body protection

■

should comply with EN 381-11 and be CE marked

GETTING  STARTED

See page 277.

1.  Wear full eye protection, ear protection, non-slip 

heavy-duty gloves, substantial footwear, and protective 

clothing at all times while operating the product. Do not 

operate the product when barefoot or wearing open 

sandals.

2.  Remove the parts from the packaging. Inspect the 

product carefully for damage. If any parts are damaged 

or missing, contact an authorised service centre.

3.  Add chain lubricating oil. Clear the surface around the 

oil cap to prevent contamination. Remove the cap from 

the oil tank. Pour the oil into the oil tank and monitor 

the oil level gauge. Ensure that no dirt enters the oil 

tank while filling. Close the oil tank, and tighten the cap. 

Wipe away any spillage.

 WARNING

Never work without chain lubricant. If the saw chain is 

running without lubricant, the guide bar and the saw 

chain can be damaged. It is essential to frequently check 

the oil level in the oil level gauge and before starting to 

use the chainsaw.

NOTE:

 Ensure that the lubricant flow screw is set to open 

for chain and bar oil to be released.

–

Turn  the screw counterclockwise to open and 

increase the oil flow to the chain and bar. 

–

Turn the screw clockwise to decrease the oil flow to 

the chain and bar. 

A properly functioning chain and bar lubricating system will 

normally discharge oil from the chain during use. To check 

the functionality of the chain and bar lubricating system, 

point the tip of the chain at a light coloured surface, such 

as a newspaper. A distinct line of oil splatter should be 

observed after a short time.

4.  Remove the guide bar cover.

5.  Adjust the chain tension. Turn the chain tensioner 

knob counterclockwise to unlock the chain tensioner 

adjustment ring. Check the chain tension frequently 

while adjusting the tension.

–

To increase the chain tension, turn the chain 

tensioner adjustment ring clockwise.

–

To reduce the chain tension, turn the chain 

tensioner adjustment ring counterclockwise.

NOTE:

 The chain tension is correct when the gap 

between the cutter in the chain and the bar is between 

3-4 mm. Pull the chain in the middle of the lower side of 

the bar downwards (away from the bar), and measure 

the distance between the bar and the chain cutters.

NOTE:

 The temperature of the chain increases during 

normal operation causing the chain to stretch. Check 

the chain tension frequently and adjust as required. 

A chain tensioned while warm may be too tight upon 

cooling. Make sure that the chain tension is correctly 

adjusted as specified in these instructions.

6.  Tighten the chain tensioner knob by turning it clockwise.

7.  Align  the raised ribs on the battery pack with the 

grooves in the product’s battery port. Make sure that 

the latch of the battery pack snaps in place and that  

the battery pack is fully seated and securely attached 

before beginning operation.

 WARNING

Always hold the product with your right hand on the rear 

handle and your left hand on the front handle.

 WARNING

Grip both handles with the thumbs and fingers encircling 

the handles. Ensure that your left hand is holding the 

front handle so that your thumb is underneath.

8.  Start the product. Set the chain brake into the run 

position by grasping the top of the chain brake lever/

hand guard and pulling towards the front handle until 

you hear a click. Pull the trigger release. Press the 

throttle trigger.

NOTE:

 To stop the product, engage the chain brake by 

rotating your left hand around the front handle. Allow the 

back of your hand to push the chain brake lever/hand guard 

toward the bar while the chain is rotating rapidly. Push the 

trigger release and release the throttle trigger.

INSTRUCTIONS CONCERNING THE PROPER 

TECHNIQUES FOR BASIC FELLING, LIMBING, AND 

CROSS-CUTTING

Understanding the forces within the wood

When you understand the directional pressures and 

stresses inside the wood you can reduce the “pinches” or 

at least expect them during your cutting. Tension in the 

wood means the fibers are being pulled apart and if you cut 

in this area, the “kerf” or cut will tend to open as the saw 

goes through. If a log is being supported on a saw horse 

and the end is hanging unsupported over the end then 

tension is created on the upper surface due to the weight 

of  the  overhanging  log  stretching  the  fibers.  Likewise,  the 
underside  of  the  log  will  be  in  compression  and  the  fibers 

are being pushed together. If a cut is made in this area, the 

kerf will have the tendency to close up during the cut. This 

would pinch the blade.

Push and pull

The reaction force is always opposite to the direction the 

chain is moving. Thus, the operator must be ready to 

control the tendency for the product to pull away (forward 

motion) when cutting on the bottom edge of the bar and the 

push backwards (towards the operator) when cutting along 

the top edge.