Электропилы Greenworks GD60CS40K2 60 В, с АКБ 2 А*ч и ЗУ 2006907UA - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
• The location of larger branches.
• The wind direction.
• There are no dirt, stones, loose bark, nails, and
staples on the tree.
1. Make a lower level notching cut. Make sure that this
cut is
a) 1/3 wide of the diameter of the tree.
b) Perpendicular to the felling direction.
CAUTION
The level notching cut helps prevent pinching of
the saw chain or the guide bar when you make the
second notch.
2. Make the felling cut no less than 50 mm and higher
than the level notching cut. Make sure that this cut
a) Is parallel to the level notching cut.
b) Keeps sufficient wood to become a hinge which
prevents the tree from twisting and felling to the
wrong direction.
When the felling cut gets near the hinge, the tree
falls. Stop the felling cut if the tree
• Does not fall to the correct direction or
• Move rearward and forward and stuck the chain.
3. Use felling wedge to open the cut and let the tree
fall to the correct direction.
4. When the tree starts to fall,
a) Remove the chainsaw from the cut.
b) Stop the machine.
c) Put the machine down.
d) Go away through the escape path. Be careful
with overhead branches and your footing.
4.7
LIMB A TREE
Figure 11.
Limbing is to remove the branches from a fallen tree.
1. Keep the larger lower branches to hold the log off
the ground.
2. Remove the small limbs in one cut.
3. Limb the branches with tension from the bottom to
up.
4. Keep the larger lower branches as a support until
the log is limbed.
4.8
BUCK A LOG
Figure 12-15.
Bucking is to cut a log into lengths. Keep your body
balance. If it is possible, lift the log and hold it with
branches, logs or chock.
• When the log is held along the full length, cut it from
the top.
• When the log is held on one end,
1. Cut the first time 1/3 of the diameter from the
bottom.
2. Cut the second time from the top to complete the
bucking.
• When the log is held on two ends,
1. Cut the first time 1/3 of the diameter from the
top.
2. Cut the second time lower 2/3 from the bottom to
complete the bucking.
• When the log is on a slope,
1. Stand on the uphill side.
2. Control the chainsaw.
3. Hold the handles tightly.
4. Release the cut pressure near the end of the
cut.
NOTE
Do not let the chain touch the ground.
When bucking is complete,
1. Release the trigger.
2. Stop the chainsaw fully.
3. Move the chainsaw from tree to tree.
5
MAINTENANCE
CAUTION
Do not let brake fluids, gasoline, petroleum-based
materials touch the plastic parts. Chemicals can cause
damage to the plastic, and make the plastic
unserviceable.
CAUTION
Do not use strong solvents or detergents on the plastic
housing or components.
WARNING
Remove the battery pack from the machine before
maintenance.
5.1
ADJUST THE CHAIN TENSION
Figure 2-7.
The more you use a chain the longer it becomes. It is
therefore important to adjust the chain regularly to take
up the slack.
Tension the chain as tightly as possible, but not so tight
that you cannot pull it round freely by hand.
7
English
EN
