Bosch GKS 55 GCE - Инструкция по эксплуатации - Страница 19

 English | 

19

Bosch Power Tools

2 609 932 800 | (8.4.11)

Sawing with Parallel Guide (see figure D)

The parallel guide 

12

 enables exact cuts along a workpiece 

edge and cutting strips of the same dimension.
Loosen wing bolt 

7

 and slide the scale of the parallel guide 

12

through the guide in the base plate 

15

. Adjust the desired cut-

ting width as the scale setting at the respective cutting mark 

9

or 

10

; see Section “Cutting Marks”. Tighten wing bolt 

7

 again.

Sawing with Auxiliary Guide (see figure E)

For sawing large workpieces or straight edges, a board or 

strip can clamped to the workpiece as an auxiliary guide; the 

base plate of the circular saw can be guided alongside the aux-

iliary guide.

Sawing with Guide Rail (GKS 55 GCE) (see figure F – G)

The guide rail 

29

 is used to carry out straight cuts.

The rubber lip on the guide rail acts as a splinter guard; it pre-

vents fraying of the surface while sawing wooden materials. 

For this, the teeth of the saw blade must face directly against 

the rubber lip.
Prior to the very first cut, the rubber lip must be adapted with 

the guide rail 

29

 to the circular saw being used. For this, place 

the guide rail 

29

 over its complete length on a workpiece. Ad-

just a cutting depth of approx. 9 mm and the saw blade to a ze-

ro degree angle. Switch the circular saw on and guide it uni-

formly and with light feed in the cutting direction.
Two guide rails can be connected to one with use of the con-

nection piece 

30

. Clamping is carried out with the four screws 

located in the connection piece.

Maintenance and Service

Maintenance and Cleaning

f

Before any work on the machine itself, pull the mains 

plug.

f

For safe and proper working, always keep the machine 

and ventilation slots clean.

The retracting blade guard must always be able to move freely 

and retract automatically. Therefore, always keep the area 

around the retracting blade guard clean. Remove dust and 

chips by blowing out with compressed air or with a brush.
Saw blades that are not coated can be protected against cor-

rosion with a thin coat of acid-free oil. Before use, the oil must 

be removed again, otherwise the wood will become soiled.
Resin and glue residue on the saw blade produces poor cuts. 

Therefore, clean the saw blade immediately after use.
If the machine should fail despite the care taken in manufac-

turing and testing procedures, repair should be carried out by 

an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-

clude the 10-digit article number given on the type plate of 

the machine.

After-sales Service and Customer Assistance

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare 

parts. Exploded views and information on spare parts can al-

so be found under:

www.bosch-pt.com

Our customer service representatives can answer your ques-

tions concerning possible applications and adjustment of 

products and accessories.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham

Uxbridge

UB 9 5HJ

Tel. Service: +44 (0844) 736 0109

Fax: +44 (0844) 736 0146

E-Mail: boschservicecentre@bosch.com

Ireland

Origo Ltd.

Unit 23 Magna Drive

Magna Business Park

City West

Dublin 24

Tel. Service: +353 (01) 4 66 67 00

Fax: +353 (01) 4 66 68 88

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.

Power Tools

Locked Bag 66

Clayton South VIC 3169

Customer Contact Center

Inside Australia:

Phone: +61 (01300) 307 044

Fax: +61 (01300) 307 045

Inside New Zealand:

Phone: +64 (0800) 543 353

Fax: +64 (0800) 428 570

Outside AU and NZ:

Phone: +61 (03) 9541 5555

www.bosch.com.au

Republic of South Africa
Customer service

Hotline: +27 (011) 6 51 96 00

Gauteng – BSC Service Centre

35 Roper Street, New Centre

Johannesburg

Tel.: +27 (011) 4 93 93 75

Fax: +27 (011) 4 93 01 26

E-Mail: bsctools@icon.co.za

KZN – BSC Service Centre

Unit E, Almar Centre

143 Crompton Street

Pinetown

Tel.: +27 (031) 7 01 21 20

Fax: +27 (031) 7 01 24 46

E-Mail: bsc.dur@za.bosch.com

OBJ_BUCH-244-004.book  Page 19  Friday, April 8, 2011  10:03 AM