Panasonic ER-131 - Инструкция по эксплуатации - Страница 6

6

How to use

<Charging instructions>

1) Set the switch to “0” , and plug

t h e   c o r d   i n t o   t h e   c l i p p e r   b o d y .
(Fig.1)

2) Plug the AC adaptor into an AC

o u t l e t .   T h e   c h a r g i n g   i n d i c a t o r
lamp will light up. (Fig.2)

3) W h e n   c h a r g i n g   i s   c o m p l e t e d

unplug the AC adaptor from an
AC outlet. The charging time is 8
hours; 1 full charge will provide
a p p r o x i m a t e l y   3 0   m i n u t e s   o f
continuous operation.

<AC operation>

1) Connect the AC adaptor to the

b o d y   i n   t h e   s a m e   w a y   a s   f o r
charging, and set the switch to “1”
to use the clipper.

2) If the AC adaptor is connected

w h i l e   t h e   s w i t c h   i s   i n   t h e   “ 1 ”
p o s i t i o n ,   t h e   c l i p p e r   m a y   n o t
operate. If this occurs, set the
switch to the “0” position, wait
about 1 minute and then set it
back to the “1” position.

3) B e   s u r e   t o   s e t   t h e   s w i t c h   “ 0 ”   t o

when finished using the clipper. If
the switch is left in the “1” position,
t h e   r e c h a r g e a b l e   b a t t e r y   w i l l
b e c o m e   c o m p l e t e l y   d i s c h a r g e d ,
shortening the life of the battery.

<3/6mm, 9/12mm comb
attachments>

1) The cutting heights are indicated

on the insides and sides of the

attachments, so be sure to look
for the height indication in order
to mount the attachment correctly
for the desired cutting height. 

2) To mount the comb attachment to

the clipper, place one side of the
hooks of the comb attachment into
the attachment mounting 

B

, then

s l i d e   t h e   o t h e r   s i d e   t o   a n o t h e r
m o u n t i n g  

B

i n   t h e   d i r e c t i o n

indicated with the arrow. (Fig.3)

3) To remove the comb attachment

from the clipper, slide one side of
the attachment off the mounting 

B

in the direction indicated with the
arrow. (Fig.4)

<Trimming With No
Attachments>

1) Cut hair by placing the clipper head

directly on the scalp. (Fig.5)

Cutting without an attachment will
trim hair length to 1mm or less.

<Mounting and removal of
the blade>

1) H o l d   t h e   c l i p p e r   b o d y   w i t h   t h e

“Panasonic” mark facing upward
a n d   p u s h   t h e   b l a d e   w i t h   y o u r
thumb in the direction indicated
by the arrow. When doing this,
c a t c h   t h e   b l a d e   i n   y o u r   o t h e r
hand. Be sure the switch is set to
“0” before attempting to remove
the blade. (Fig.6)

2) T o   r e m o u n t   t h e   b l a d e ,   f i t   t h e

m o u n t i n g   h o o k   i n t o   t h e   b l a d e
mounting on the clipper body and
push in until it “clicks”. (Fig.7)

04̲08̲ER131取説(欧州)    06.02.27  12:58    ページ 6