Profi Cook PC-HWS 1145 - Инструкция по эксплуатации - Страница 38

38

PC-HWS1145_IM_new

22.09.17

Standby (Standby Mode)
Connect the mains cable to a properly installed and earthed 

wall outlet. The “Lock” button is illuminated. The notification 

“0” will appear in the display. The appliance is in standby 

mode.

Control Panel
The appliance features touch buttons. A slight touch of the 

control panel with the finger is enough. Use the fingertip, not 

the top of the finger.

Button Functions
Lock 

Lock / unlock the appliance:

To unlock the appliance touch the button for 

3 seconds. The appliance will switch back 

into Standby if you did not touch a button for 

10 seconds.

Temp. 

Setting the water temperature in °C:

000 / 55 / 65 / 75 / 85 / 100

Volume 

Setting the water volume in ml:

100 / 200 / 300 / 400 / 500

Start / Stop  Start or premature stop of dispensing water

Functionality of the Appliance

• 

The appliance will save the temperature and quantity 

setting selected last as long the power plug has not been 

removed from the socket.

• 

Once the selected amount of water has been dispensed 

the appliance will stop dispensing automatically. You will 

hear signal tones. 

• 

The appliance emitts different signal tones:

- 

6 signal tones:  Water discharge completed.

- 

10 signal tones:  Water discharge incomplete

- 

20 signal tones:  Water tank empty (error message “E7”)

First Use

 CAUTION:

Before first use cold water must run through the heating 

system to avoid activating the over temperature protection.

1.  Fill the water tank with clean, fresh water to the MAX 

marking. Close the lid again.

2. 

Place an empty vessel with a minimum volume of 500 ml 

onto the drip tray cover.

3. 

Touch the “Lock” button for 3 seconds to unlock the 

appliance. The “Temp.” and “Volume” buttons are illumi

-

nated. The temperature and water volume is shown in 

the display.

4.  Check the temperature setting. It must be set to “000”.

5.  Tap the “Volume” button until “500” is shown in the 

display.

6. 

To start dispensing water tap the “Start / Stop” button.

7.  Once the water discharge is completed you will hear 6 

signal tones. Pour the dispensed water away. Place the 

vessel onto the drip tray again.

8. 

Select the temperature “100” °C.

9. 

Start the water dispense once again. This procedure is 

necessary in order to enable the appliance to identify the 

boiling point.

The water dispenser is now ready to use.

  NOTE:

If you accidentally heat up the water to 100 °C during first 

use the over temperature protection of the appliance may 

be activated. During the next use the appliance would 

dispense cold water only. In this case refer to “

Trouble-

shooting

”.

Operation

 WARNING: 

Danger of scalding due to escaping steam!

While preparing hot water keep your hands away from the 

faucet.

  NOTE:

Always use fresh, cold water.

1.  Ensure that a sufficient amount of water is left in the tank.

2. 

Place a vessel with the desired volume onto the drip tray.

3. 

Unlock the appliance with the “Lock” button.

4.  Tap the “Temp.” button to set the desired temperature.

5.  Tap the “Volume” button to select the desired amount of 

water.

6. 

Start dispensing water by tapping the “Start / Stop” button.

  NOTE:

Tap the “Start / Stop” button to interrupt the water 

dispenser.

De-scaling

Decalcification is necessary if preparation time increases 

or if the amount of water issued varies. In any case, we 

recommend that you decalcify the appliance after filling the 

tank 2 - 4 times, depending on the degree of hardness of your 

tap water.
• 

Use only commercially available citrus acid-based de-

scaler.

• 

Follow the recommended instructions for use.

• 

Dispense hot water with a temperature of 100 °C once. 

Do not pour that water away immediately. As long as it 

is hot you may still use it to de-scale the water faucet if 

needed. Please observe the instructions that we have 

included in the chapter “

Cleaning

”.

 WARNING:

• 

Then dispense the biggest volume (500 ml) of hot water 

with a temperature of 100 °C for three times in order to 

rinse any residues of de-scaling agent.

• 

Do not use this water for consumption.