Redmond RK-M142-E - Инструкция по эксплуатации - Страница 7

7

RK-M142-E

GBR

No serial number identification sticker on the appliance automatically disables 

the user’s right to aftersale service .
Wipe the base of the appliance with a damp cloth, then let dry. You may notice 

foreign smell when first using the appliance, this does not mean its malfunction. 

After the appliance transportation or storage at low temperature keep it at 

room temperature for at least two hours before plugging in.
You are advised to boil water in the kettle a few times before use to get foreign 

smell out and disinfect the appliance.

I I.  O P E R AT I O N 

Preparation 

1.  Fix the kettle with the base to the solid even dry horizontal surface. Make 

sure the outgoing vapour during boiling does not fall on wallpaper, 

decorative coats, electric units and other items, which can be damaged 

by humidity and high temperature.    

2.  Unwind the power cord to the desired length. Put the excessive part into 

the recess at the bottom of the stand. Use the extender of appropriate 

capacity if necessary (no less than 2.5 kW). 

3.  Lift the kettle off the base. Press the opening button on the appliance 

lever. 

4.  Pour water into the kettle. Water level should be between minimum and 

maximum levels on the inner surface of the appliance frame. If the kettle 

is overfilled it could cause boil-over. The unit will turn off prematurely 

in case of water shortage.

ATTENTION! The unit is meant only for water heating and boiling.   

5. 

Firmly close the kettle lid and fix it to the base. The unit will work only 

if it is fixed correctly. 

6.  Plug in the kettle.

Water boiling 

1.  Press the «0/I» button. A short audible signal will be heard, and the process 

of water heating will start. Button illumination will light up solid during 

the operation. 

2.  The appliance will be automatically turned off after boiling.   

3.  To interrupt the heating process lift the «0/I» button.

The settings are saved if the kettle is lifted off the base during operation. The appli-

ance operation will be restarted automatically after returning the kettle to the base. 

Safety system 

•  The kettle is supplied with an automatic shut-off system upon boiling.

•  In case of water shortage the automatic overheat protection will turn off 

the kettle. Wait till the appliance is cooled, thereafter it will be ready for 

operation. 

I I I.  C L E A N I N G A N D  M A I N T E N A N C E 

Unplug the kettle and allow it to cool before cleaning. 

DO NOT USE solvents (petrol, acetone, etc.), abrasive cleansers, and abrasive 

coated sponges while cleaning. 
ATTENTION! Before repeated usage make sure that the electrical contacts are kept dry! 

Base and body cleaning 

Clean the kettle body and base with a soft cloth. Dry the kettle before operation. 

ATTENTION! Never immerse the kettle, the base, the power cord or the socket 

in water: the electrical contacts should not contact with water. 

Descaling 

During operation, depending on the composition of usable water, oxide spots 

and scale can appear on the heating element and inner walls of the appliance. 

To remove it use special nonabrasive cleansers for scale cleaning and removal 

from kitchen appliances. 

1.  Pour water into the kettle ¾ from maximum capacity and bring to a boil.   

2.  After the kettle turns off, add eight percent acetic acid solution to the 

maximum level on the inner surface of the body. 

3.  Leave this solution inside the kettle for several hours. 

4.  Empty the kettle and rinse properly.

5.  Fill the kettle with clean water up to the maximum level on the inner 

surface of the body and bring it to boil. 

6.  Empty the kettle and rinse it again. If scale still remains, repeat the 

procedure mentioned above. 

You can also use special means for descaling. Follow manufacturer’s instructions 

in this case.  

Removable scale filter cleansing 

1. 

Open the lid. Remove the filter pulling it upward. 

2. 

Rinse the filter. You can use a dishwashing solution. 

3. 

Place the filter into the kettle with the projection to the centre.