BRAYER BR1202 - Инструкция по эксплуатации - Страница 5

8

9

EN

EN

If you are going to use the vacuum lid (3) intended 

for longer storage of the prepared mixture, the 

maximal amount should not exceed 500 ml.

• Install the knife block (5) in the bottle (4) and turn the 

knife block (5) counterclockwise (left-hand thread). 

 Do not make excessive efforts while turning the knife 

block (5).
• Once again make sure that the knife block (5) is 

installed correctly.
• Put the necessary ingredients in the bottle (4) and add 

the required amount of liquid.
• Install the assembled vacuum lid (3) on the upper part 

of the bottle (4) and thread it rotating clockwise. Do not 

apply excessive efforts when screwing the lid (3).

• Install the protective lid (16) on the vacuum lid (3) and 

turn it clockwise until bumping.
• Match the mark « » on the bottle (4) with the mark     

« » on the motor unit (6), insert the bottle (4) into the 

motor unit (6) body and turn the bottle (4) clockwise until 

bumping. Make sure that the bottle (4) is fixed properly.

• Before switching the blender on you should decide 

how you will use the prepared mixture - use it 

immediately or store it in the fridge. 

1. Using the processed products:

- insert the power plug into the mains socket, the 

blender will switch on;

- do not exceed the recommended operation time. After 

chopping the products unplug the unit;
- turn the bottle (4) counterclockwise and remove it from 

the motor unit (6);
- turn over the bottle (4) and remove the knife block (5) 

turning it clockwise;
- take the processed products out of the bottle (4);

- if you are going to take the bottle (4) with you, flip 

the bottle (4) and remove the knife block (5) turning it 

clockwise, install the lid (7) on the bottle (4) turning it 

counterclockwise. When you use the lid (7), open the 

valve, add the necessary amount of the product and 

close the valve.

Note:

 You can leave the vacuum pump (2) on the lid 

(3) and after consuming the product turn over the bottle 

(4) and press the button (1) to create vacuum in the 

bottle (4). It provides the best conditions for the product 

storing.
• After removing the knife block (5) wash it (from the 

knives side only) and dry.

2. Storing the processed products in the bottle (4) 
ATTENTION!
If you are going to use the vacuum lid (3) intended 

for longer storage of the prepared mixture, the 

maximal amount should not exceed 500 ml.
Before using the vacuum lid (3) make sure that it is 

assembled correctly and installed properly on the 

blender bottle (4).
Do not switch the vacuum pump (2) on if the 

blender bottle (4) is turned upside down, if the 

bottle (4) is vibrating during the blender operation 

or if the bottle (4) is tilted. 
If you accidentally tilted the bottle at more than 

90 degrees, the vacuum pump will switch off 

automatically.
Do not open the back-pressure valve (11) if the 

bottle (4) is turned upside down. 

- press the button (1) «   », the vacuum pump will 

switch on for approximately 1 minute (the operation 

time of the vacuum pump depends on the amount of the 

ingredients in the bottle (4));

Note:

 fix operation time limits for the vacuum pump. 

After 3 minutes of operation make at least 30 minutes 

break.

- to check whether there is vacuum in the bottle (4) 

remove the vacuum pump (2) and pull the back-

pressure valve (11). If you hear a sound of air entering 

the bottle (4), it means that the vacuum lid (3) is in good 

working order. Install the vacuum pump (2) on the lid (3) 

and switch it on again pressing the button (1) «   ».
- remove the vacuum pump (2) by turning it 

counterclockwise;
- install the protective lid (16) instead of the vacuum 

pump (2) and turn it clockwise;
- insert the power plug into the mains socket, the 

blender will switch on;
- do not exceed the recommended operation time. After 

chopping the products unplug the unit;
- turn the bottle (4) counterclockwise and remove it from 

the motor unit (6);
- remove the vacuum pump (2) turning it 

counterclockwise;
– put the bottle (4) in the fridge for storage;

Note: 

vacuum in the bottle (4) extends the storage 

life of the processed products, but not for an indefinite 

period of time. Before consuming check the product 

carefully and if you find any signs of spoilage, do not 

consume it.
– before removing the vacuum lid (3) you have to admit 

air to the bottle (4), remove the protective lid (16) by 

ATTENTION: The knife block (5) cutting edges are 

very sharp and dangerous. Handle the knife block 

(5) carefully.