Braun HB901AI-MQ9125XS - Инструкция по эксплуатации - Страница 14

14

How to Use the Appliance 

Smartspeed Switch for 
Variable Speeds  

One squeeze, all speeds. The more you press, the 
higher the speed. The higher the speed, the faster 
and finer the blending and chopping results.

One handed operation: the Smartspeed switch (3) 
allows you to turn on the appliance and control the 
speed with one hand.

Operating your Hand Blender

First use: Remove the transportation lock from the 
motor part (4) by pulling it at the red strap.

Switching On (A)

The appliance comes with an imode selector (1) 
and a safety button (2) for releasing the 
Smartspeed switch (3). Please follow the instruction 
to start the appliance: 

• 

By pressing the silver part of the top you can 
choose one of the 3 different imodes (high 
speed, low speed, pulse). 

• 

W ith the help of the 3 modes you can decide how 
to process the food.  The indicator light glows 
white to show the chosen mode.

• 

High speed (1a) gives you the full speed 
available. It is the standard position of the mode.

• 

Low speed (1b) decreases the speed even if you 
press the Smartspeed switch fully.

• 

The pulse mode (1c) can be used to break apart 
larger pieces of food or to control the texture of 
food when chopping. Press the Smartspeed 
switch for short bursts of power.

• 

After choosing the mode, press the safety button 
(2) with your thumb. 

• 

Immediately press the Smartspeed switch and 
adjust to the desired speed.
NOTE: If the Smartspeed switch is not pressed 
within 2 seconds, the appliance cannot be 
switched on for safety reasons. The safety button 
light will flash red. To switch the appliance on, 
start again.

• 

During operation you do not need to keep the 
safety button pressed.

Pilot light

Appliance / Operating status

Safety button 
light Flashing red

Appliance is ready for use.

Safety button 
light off

Appliance is released (switch 
release button is pressed) and 
can be switched on.

Standby mode 
after 10 minutes. 
All lights switch 
off.

Device is active again if any 
button is pressed

Safety button light 
solid red and 
imode selector 
lights are all 
flashing

Device is overheated. Let the 
device cool down one hour. It 
is ready for use again when 
the imode selector light stops 
flashing and the safety button 
light flashes.

ActiveBlade Shaft (B)

The hand blender is equipped with an ActiveBlade 
shaft, which enables the knife extend to the bottom 
of the bell. The adjustment is made automatically by 
pressure required in blending tasks, especially 
suited to mix hard foods e.g. raw fruits and
vegetables.

It is also perfectly suited for preparing dips, sauces, 
salad dressings, soups, baby food, as well as 
drinks, smoothies and milkshakes.

For best results, use the highest speed.

Assembly and Operation

• 

Attach the ActiveBlade shaft (6) to the motor part 
until it clicks.

• 

Place the ActiveBlade shaft into the mixture to be 
blended. Then switch the appliance on as 
described above.

• 

Blend ingredients to the desired consistency 
using a gentle up-and-down motion. Depending
on the pressure applied, the ActiveBlade shaft 
will depress and blade will extend.

• 

After use, unplug the hand blender and press the 
EasyClick Plus release buttons (5) to detach the 
ActiveBlade shaft.

Caution

• 

Do not let liquids or ingredients overlap the green 
line of the ActiveBlade shaft.

• 

If using the appliance to purée hot food in a 
saucepan or pot, remove the saucepan or pot
from the heat source and ensure the liquid is not 
boiling. Allow hot food to cool slightly to avoid 
risk of scalding.

• 

Do not let the hand blender sit in a hot pan on the 
cooktop when not in use.

• 

Do not scratch the ActiveBlade shaft over the 
bottom of pans and pots.

• 

Do not operate continuously for longer than 
2 minutes.

• 

Let the appliance cool down for 5 minutes before 
you continue processing.

Recipe Example: Mayonnaise
250 g oil (e.g. sunflower oil)
1 egg and 1 extra egg yolk

5722114224_HB901-MQ91-35-38-47 INT.indd   14

24.07.20   10:48